Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

The Status

The Status display tells you what is happening while the dishwasher is in operation and also any malfunctions if they occur (see page 6).
The lights will come ONindicating the sequence of operation the dishwasher is in.
SENSING Displayed during periods using CleanSensor technology to measure the amount of soil in the load and decide if another prewash is needed.
WASHING Displayed during prewash and main wash periods.
RINSING Displayed during rinse periods.
DRYING Displayed during SPEEDDRY/HEATED DRY.
SANITIZED Displayed when cycle has met sanitization conditions. Light remains ONuntil door is opened.

Load Selections

The light above the selected pad will be ON to indicate whichLOAD SELECTION has been selected.
SANIWASH Heavy 12.1 gal., 98 min., Medium 10.3 gal., 85 min., Light 8.6 gal., 82 min.
This cycle raises the water temperature in the final rinse to sanitize your dishware. The cycle length will vary depending on the temperature
of your inlet water.
NOTE: The SaniWash cycle is monitored for sanitization requirements. If the cycle is interrupted during or after the main wash portion or
if the incoming water temperature is so low that adequate water heating cannot be achieved, the sanitizing conditions will not be met.
In these cases, the sanitized light will not illuminate at the end of the cycle.
POTS & PANS Heavy 13.1 gal., 100 min., Medium 11.5 gal., 71 min., Light 11.5 gal., 58 min.
For heavily soiled dishes or cookware with dried-on or baked-on soils.
Everyday dishes may be included. This cycle will not remove
burned-on foods.
NORMAL
Heavy 11.5 gal., 80 min., Medium 9.8 gal., 54 min., Light 8.2 gal., 42 min.
For loads of everyday dishes, glasses and cookware with medium soils.
NOTE:Many dishes have lighter soil than normal. Choosing a
cycle other than NORMAL will save energy and water.
SPEEDWASH/
Heavy 10 gal., 39 min., Medium 8.3 gal., 28 min., Light 6.7 gal., 24 min.
LIGHTWASH For dishes with light soils.
CHINA CRYSTAL
Heavy 9.8 gal., 53 min., Medium 8.2 gal., 30 min., Light 8.2 gal., 25 min.
For lightly soiled china and crystal.
RINSE ONLY
Heavy 3.3 gal., 6 min., Light 1.6 gal., 3 min.
For rinsing partial loads that will be washed later. Do not use detergent.
NOTE: The dishwasher is equipped with Clean Sensor technology; therefore, cycle length and time may vary depending on soil and temperature conditions.

Options

The light above the selected pad will be ONto indicate which OPTION has been selected.
POWER For use with heavily soiled and/or dried-on, baked-on soils. This option MUSTbe selected PRIOR to starting the cycle.
PRESOAK This option adds 16 minutes to the cycle time.
SPEEDDRY/ Shuts off the drying heat option. Dishes air dry naturally and energy is saved. You can prop the door open after the CLEAN light
HEATEDDRY illuminates.
OFF
SPEEDDRY/ Turns the heater on for fast drying. This cycle will extend the time to your wash cycle by 40 minutes for the NORMAL, CHINA
HEATEDDRY CRYSTAL and POTS & PANScycle and 8 minutes for the SPEED WASH/LIGHT WASH and SANI WASH cycle.
ON NOTE:Cannot be selected with RINSE ONLY cycle.
LOCK
When the LOCK pad is touched twice within 3 seconds, all pads become inoperative. You can lock the controls to prevent any selections
from being made. Or you can lock the controls after you have
started a cycle or selected DELAY START so the cycle orDELAY START
is not interrupted.
Children cannot accidentally start dishwasher by touching pads with this option selected.
To unlock the dishwasher after it has been locked, touch the
LOCK
pad twice within 3 seconds. The light above the
LOCK
pad will turn off.
DELAY HOURS You can delay the start of a wash cycle for up to 8 hours. Press the DELAYHOURSpad to choose the number of hours you want to
delay
the start of the cycle, then press START/RESET. The machine will count down and start automatically
at the correct time. Pressing
START/RESET a second time will cancel the DELAYSTART selection. NOTE: If you forget to fully close the door, a reminder
signal will beep until you do so.
RESET To change a cycle after washing starts, touch the START/RESETpad to cancel the cycle. After water is pumped out and the motor
stops, you can reprogram and restart the dishwasher. This will take approximately 90 seconds.

Start

Close and latch the door. Touch the START/RESETpad to begin the cycle. Water fill begins, and approximately 60 seconds later
the wash action begins.
NOTE: The dishwasher remembers your last cycle so you don’t have to reprogram each time. When the dishwasher is loaded and
the door latch is in the locked position, the control panel lights will be ON and display the last settings you selected.
If you don’t want to change any of the settings, simply touch the START/RESET pad to begin the cycle.
Also, if a power failure occurs,NORMAL and SPEED DRY/HEATED DRY will automatically be programmed. Make any new selections
and touch the START/RESET pad to begin the cycle.

Clean

This light is illuminated when a wash cycle is complete. The light will stay ON until the door is opened.
Control Settings

GEAppliances.com

5