49-40356-1v01 5/11/04 3:59 PM Page 14

Safety Instructions

Operating Instructions

Troubleshooting Tips

Consumer Support

About changing the power level.

The power level may be entered or changed immediately after entering the feature time for TIME COOK, TIME DEFROST or EXPRESS COOK. The power level may also be changed during time countdown.

 

Press TIME COOK or select Time Defrost.

1

 

Enter cooking or defrosting time.

2

 

Press POWER LEVEL.

3

 

Select desired power level 1–10.

4

 

Press START.

5

Variable power levels add flexibility to microwave cooking. The power levels on the microwave oven can be compared to the surface units on a range.

Each power level gives you microwave energy a certain percent of the time. Power level 7 is microwave energy 70% of the time. Power level 3 is energy 30% of the time. Most cooking will be done on High (power level 10) which gives you 100% power. Power level 10 will cook faster but food may need more frequent stirring, rotating or turning over. A lower setting will cook more evenly and need less stirring or rotating of the food. Some foods may have better flavor, texture or appearance if one of the lower settings is used. Use

a lower power level when cooking foods that have a tendency to boil over, such as scalloped potatoes.

Rest periods (when the microwave energy cycles off) give time for the food to “equalize” or transfer heat to the inside of the food. An example of this is shown with power level 3—the defrost cycle. If microwave energy did not cycle off, the outside of the food would cook before the inside was defrosted.

Here are some examples of uses for various power levels:

High 10: Fish, bacon, vegetables, boiling liquids.

Med-High 7: Gentle cooking of meat and poultry; baking casseroles and reheating.

Medium 5: Slow cooking and tenderizing for stews and less tender cuts of meat.

Low 2 or 3: Defrosting; simmering; delicate sauces.

Warm 1: Keeping food warm; softening butter.

14

Page 14
Image 14
GE JEM31 About changing the power level, Press Power Level, Here are some examples of uses for various power levels

JEM31 specifications

The GE JEM31 is a notable industrial generator set produced by General Electric (GE), known for its reliability and robust performance in power generation. This generator set is designed to meet the diverse requirements of various industrial applications, making it a preferred choice for businesses seeking uninterrupted power supply.

One of the main features of the GE JEM31 is its advanced engine technology. It typically comes equipped with a high-performance, diesel or gas engine that ensures efficient fuel consumption while delivering substantial power output. This engine is engineered for durability and extended operational life, catering to users who require a dependable power source for both prime and backup applications.

The JEM31 boasts a compact design, making it suitable for limited space installations. Despite its smaller footprint, it does not compromise on performance or features. The generator set is often outfitted with sound attenuation measures, which help reduce operational noise – a crucial factor for environments where noise pollution must be minimized.

In terms of technology, the GE JEM31 incorporates sophisticated control and monitoring systems. These systems allow users to easily manage the generator’s performance and monitor key operational metrics in real time. This includes features like remote monitoring capabilities, fault diagnostics, and automatic shut-off mechanisms to prevent damage in case of system failure.

The generator's fuel efficiency is further enhanced by innovative design aspects such as optimized combustion processes and advanced cooling systems. This allows the JEM31 to operate in a wide variety of environmental conditions while maintaining peak efficiency, making it adaptable for use in different geographical locations.

Durability is another critical characteristic of the GE JEM31. Designed to withstand harsh industrial environments, the generator set is often constructed with high-quality materials resistant to corrosion and wear. This longevity translates into lower maintenance costs and extended service intervals, providing excellent value for businesses that rely on consistent power availability.

In conclusion, the GE JEM31 represents a well-engineered solution for industrial power needs. Its robust engine technology, compact design, advanced control systems, and durable construction make it a reliable choice for various applications, whether for prime power or standby use. The combination of performance, efficiency, and adaptability positions the JEM31 as a solid investment for companies looking to enhance their operational resilience.