GE PSB1201NSS dimensions GE Profile Advantium 120 Volt - 30 Wall Oven, Installation Information

PSB1201NSS

GE Profile Advantium® 120 Volt - 30" Wall Oven

Advantium wall oven/GE Profile cooking tower dimensions and cabinet installation information (in inches)

Note: 2" minimum						Cabinet width		4-3/16
	A= Allow 1" overlap of oven over bottom edge of cutout, and allow
between cutouts when
	1-1/4" overlap at top edge of cutout.
installed above warming	B= Allow 11/16"-3/4" for overlap of oven over side edges of cutout.								Junction box location (240-volt models only)
drawer or single wall oven.			23-1/2"				A	B
Installation Information:			Cutout depth	4-3/16"	H
Before installing, consult							D
									2-1/2" MIN between cutouts
installation instructions	21-1/2"					Excluding
									recommended—2" MIN required
						Handle
	Excluding				W
packed with product for ­
	Handle
				Junction
current dimensional data.							A
			A	box location				B
									Construct Solid Bottom
Note: PSB1200/1 series			B			Conduit			MIN 3/8" Plywood Supported by
		Conduit	17-1/2"			(46" long)			2 x 4 or 1 x 2 Runners, all Four Sides.
Advantium can be				Construct Solid
	19-1/32"	(48-1/2"	Cutout height						(Must Support 150 lbs. for Advantium)
installed below GE/GE		long)		Bottom Min.					(Must Support 200 lbs. for Wall Oven)
				3/8" Plywood
Profile non-downdraft				Supported by					9-1/4" cutout height
gas and electric cooktops.				2 x 4 or 1 x 2
				Runners, all					28-1/2" cutout width
It CANNOT be installed	29-25/32"			Four Sides.					2" MIN between cutouts
below induction or Monogram				(Must Support
			5" min.from 150 lbs.)
(2GU3841385) gas cooktops.			floor 1" min.
Note: PSB1200/1 series Advantium		30"	above toekick
									1" Min. above toekick or adjust
			Note: Cabinets installed adjacent
oven comes with two lower trim pieces.									to oven installation height
			to wall ovens must have an adhesion
One is for use above 36-inch height			spec of at least 194° F temperature rating.
installations and one is for use below 36-
inch installations. Use of the accessory
drawer will replace the bottom trim piece			L
for applicable installations. Please see
			C	2 x 4’s or
installation instructions for full details.								D			Z
				equivalent
					Cabinet	W	H	Depth	X	Y	Cutout
				solid floor
					Width	Width	Height	(excluding	Cutout	Cutout	Depth
					(inches)			handle)	Width	Height	(minimum)
				PSB1200/1 without	30	29-25/32	19-1/8	21-3/4	25-1/8	17-1/2	23-1/2
For answers to your Monogram,® GE Profile™ or				accessory drawer
				PSB1200/1 with					25-1/4 to
®					30	29-25/32	22-1/4	21-3/4		21	23-1/2
GE appliance questions, visit our website at				accessory drawer
ge.com or call GE Answer Center® service,		Suitable							28-1/2*
800.626.2000.				*For existing cutouts a maximum width of 28-1/2" is acceptable
		bracing	21-5/8"
		to support
			over centerline								Listed by
		runners
			of cabinet
											Underwriters
			(Must support 130 lbs.)								Laboratories

Specification Created 11/08 240446