PSB1201NSS
GE Profile Advantium® 120 Volt - 30" Wall Oven
Preparation with an Accessory Drawer
Prepare the opening
The Advantium PSB1200/1 series can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown.
|
|
|
|
|
| ||
* For existing cutouts, a maximum | 30” |
| |||||
|
|
|
|
|
|
| |
width of |
|
|
|
|
|
|
|
the opening is slightly wider, secure |
|
|
|
|
|
|
|
|
|
|
|
| |||
a furring strip on each side of the |
|
|
|
|
| Min. |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
cutout for securing the oven. |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
• Allow 3/4" to |
|
|
|
| |||
|
| 21” | |||||
on the sides and 7/8" overlap on the |
|
|
|
|
|
| Construct |
|
|
| |||||
Prepare the opening (cont.)
When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium and the other appliance overlaps. Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides.
•the support must be level and rigidly mounted, flush with the bottom edge of the cutout.
Installation over a GE/Monogram Oven and Warming Drawer:
|
|
| Construct Solid |
| 30” | Bottom Min. | |
|
|
| 3/8” Plywood |
|
|
| Supported by |
|
|
| 2x4 or 2x2 |
|
| Runners all | |
|
| Four Sides | |
|
| Min. |
|
|
| 21” | 2” Min. |
|
|
| (3” recommended) |
|
|
| Per Oven |
|
|
| Requirement |
5” min. |
|
|
|
from floor |
|
| 2” Min. |
1” min. |
|
| |
|
|
| |
above | Per warming drawer requirement | ||
toekick |
|
|
|
bottom of the opening for all models. |
|
| Base | |
|
| Min. 3/8” | ||
The amount of overlap on the sides | 5” min. | Plywood | ||
from floor | Supported | |||
depends on the actual cutout width. | by 2x4 or 2x2 | |||
1” min. | ||||
Runners all | ||||
Allow | above | Four Sides | ||
top for models PSB1200 and PSB1201 | toekick |
| ||
|
|
| ||
and for models ZSC1201 and ZSC1202. |
|
|
| |
• Oven overlaps will conceal cut edges on all sides of the opening. |
Note: PSB1200/1 series Advantium can be installed below GE/GE Profile |
induction or Monogram (2GU3841385) gas cooktops. |
Note: PSB1200/1 series Advantium oven comes with two lower trim |
pieces. One is for use above |
use below |
the bottom trim piece for applicable installations. Please see installation |
30”
21”
5” min. from floor 1” min. above toekick
|
| Construct | ||||||
|
|
|
| Solid Bottom | ||||
|
|
|
| |||||
|
|
|
| Min. 3/8” | ||||
|
|
|
| Plywood | ||||
|
|
|
| Supported | ||||
| by 2x4 or 2x2 | |||||||
Min. |
| Runners all | ||||||
|
|
|
| Four Sides | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2” Min. | |||
|
|
|
|
| (3” recommended) |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Per warming |
| |
|
|
|
|
|
| drawer |
| |
|
|
|
|
|
| requirement |
| |
|
|
|
|
|
|
|
|
|
Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
Caution: For personal safety, the mounting surface must be capable of supporting the cabinet load, in addition to the added weight of this approximate
instructions for full details. |
For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.
Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.
Listed by Underwriters Laboratories
Specification Created 11/08 | 240446 |
