GE PSB2201NSS dimensions GE Profile Advantium 240 Wall Oven, Preparation withan Accessory Drawer

PSB2201NSS

GE Profile Advantium® 240 Wall Oven

Preparation with an Accessory Drawer

Prepare the opening

The Advantium 240V can be installed in combination with other GE/Monogram appliances. Always follow each product's Installation Instructions to compete the installation.

Single Advantium 240V Installation:

Order a 30" wide single oven cabinet or cut the opening in a wall to the dimensions shown.

* For existing cutouts, a

			23-1/2”
maximum width of 28-1/2" is	30”
acceptable. If the opening is
slightly wider, secure a furring
			25-1/4”
strip on each side of the
			Min.
cutout for securing the oven.
• Always maintain 36-3/4"
		21”

Prepare the opening (cont.)

When installed over a single oven or a warming drawer, allow at least 2" between the two openings. This separation will provide clearance for bottom overlap of the Advantium 240V and the other appliance overlaps.

Construct a solid oven floor of 3/8" min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides.

•the support must be level and rigidly mounted, flush with the bottom edge of the cutout.

Installation over a GE/Monogram Oven and Warming Drawer:

			Construct Solid
	30”	23-1/2”	Bottom Min.
			3/8” Plywood
			Supported by
			2x4 or 2x2
		25-1/4”	Runners all
			Four Sides
		Min.
		21”	2” Min.
			(3” recommended
			Per Oven
			Requirement
5” min.
from floor			2” Min.
1” min.
above	Per warming drawer requirement
toekick

minimum height from		Construct
the floor to the cutout in		Base
any single or combined		Min. 3/8”
	5” min.	Plywood
installation.	from floor	Supported
		by 2x4 or 2
	1” min.
• Allow 3/4" to 2-1/8" case trim		Runners all
	above	Four Sides
overlap on the sides and 7/8"	toekick
overlap on the bottom of
the opening for all models.
The amount of overlap on
the sides depends on the actual cutout width. Allow 1-1/4" case
trim overlap on the top for models PSB2200 and PSB2201 and for
models ZSC2200, ZSC2201 and ZSC2202.

• Oven overlaps will conceal cut edges on all sides of the opening.

30”

21”

5” min. from floor 1” min. above toekick

23-1/2”	Construct
	Solid Bottom
	Min. 3/8”
	Plywood
	Supported
25-1/4”	by 2x4 or 2x2
Min.	Runners all
	Four Sides
		2” Min.
		(3” recommended
			Per warming
			drawer
			requirement

*For existing cutouts, a maximum width of

28-1/2" is acceptable. If the opening is slightly wider, secure a furring strip on each side of the cutout for securing the oven.

Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

Caution: For personal safety, the mounting surface must be capable of supporting the

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.

*For existing cutouts, a maximum width of

28-1/2" is acceptable. If the opening is slightly

wider, secure a furring strip on each side of the cutout for securing the oven.

Note: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. See Warming Drawer installation instructions for details.

cabinet load, in addition to the added weight of this approximate 80-pound oven and 30- pound drawer, plus additional oven loads of up to 50 pounds or a total weight of 160 pounds.

Listed by

Underwriters

Laboratories

Specification Created 9/08 240441