![](/images/new-backgrounds/1228570/2285705x1.webp)
Avoid fire hazard or electrical shock. Do not use an adaptor plug or extension cord or remove grounding prong from electrical power cord. Failure to follow this warning can cause serious injury, fire or death.
ELECTRIC DRYERS:
DRYER
FUSED 30 AMP 120/240 V OR 120/208 V WALL
CORRECT | DRYER SERVICE |
Grounding type GAS DRYERS: wall receptacle
Do not under
any circumstances cut, remove,
or bypass
the grounding prong from this plug.
Power supply
cord with
grounding plug
CORRECT Use this way ONLY
Note: The instructions appearing in this Use and Care Guide are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.
Follow fabric care label instructions.
Place small items in a mesh bag.
Fill dryer drum 1/3 to 1/2 full.
Place the front bar under
the lip of the lint screen opening.
Drying Procedures
•Follow the guidelines below for preparing the load for drying.
•Read the Operating Instructions card for operating your specific model.
•Always read and follow fabric care labels and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read Important Safety Instructions, page 2, before operating this dryer.
1.Prepare items for drying.
•Dry items of similar fabric, weight and construction in the same load.
•Separate dark items from
•Be sure buckles, buttons and trim are heatproof and won't damage the drum finish. Close zippers, fasten hooks and
•If possible, turn pockets inside out for even drying.
•Check for stains which may not have been removed in washing. Dryer heat may permanently set some stains. Repeat stain removal process before drying.
•Place small items in a mesh bag to prevent tangling and for easy removal.
2.Check that lint screen is clean and in place.
3.Load the dryer.
•The average load will fill the drum 1/3 to 1/2 full. Items need room to tumble freely for even drying and less wrinkling. Do not overload dryer.
•When drying large items, dry only 2 or 3 at a time. Fill out the load with small and medium sized items.
•For delicate or very small loads, add 2
•Do not overdry items. Overdrying can cause wrinkling, shrinkage, harshness, and a
•If desired, add a dryer fabric softener sheet.
4.Close the dryer door and select the cycle, temperature, dryness level and options desired. See Operating Instructions for your specific model information.
5.Press START to begin the cycle.
•To add or remove items when the dryer is running open the door. The dryer will stop when the door is opened. Allow the drum to come to a complete stop before reaching inside.
•Close the door and press START to resume the cycle.
6.When the cycle ends, remove items immediately and hang or fold.
Features
End of Cycle Signal
A signal will sound at the end of the cycle and periodically during Extra Care at the volume level selected. (some models)
Drum Light (some models)
A drum light will come on whenever the door is opened to illuminate the dryer drum during loading and unloading. Closing the door turns off the light.
Reversible Dryer Door
Your dryer is equipped with a reversible door. The door can be hinged on the right or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on changing the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1.Open the dryer door and remove the lint screen.
2.Insert drying rack into the dryer drum. Place the front bar under the lip of the lint screen opening.
3.Place items to be dried on top of the rack. Weight should not exceed 10 lbs. Leave space between items, but do not let items hang over the sides or through the grids. Do not tumble other items when using the drying rack.
4.Select Timed Dry. Use only the Air Fluff/No Heat option for items containing plastic, foam rubber,
5.When items are dry, remove the rack and replace the lint screen. If lint screen is not in place, tumbling items could enter the exhaust system and cause damage to the dryer.
3