GE WSKS3040E manual WMK-35 Wall Kit Installation, General Information, Dryer Mounting Position

GE Appliances

WSKS3040E – GE Spacemaker® 2.1 Cu. Ft. Stationary Washer with Stainless Steel Basket

WMK-35 Wall Kit Installation

2 x 4

24-1/2 6

5-1/8

4" Dia.

Exhaust

Both

Sides 3-1/8

33-1/4 32

DSKS433

79-1/4DSKS333

78

2 x 4

WSLP1100

WSLS1100

74-1/8WSKS3040

Standpipe

33" Minimum

38If Less Than 33" Use Syphon Break Kit WH49X228

	120V 20A or
	208-240V 30A
20" Max.	3-3/4
Opening	3
5-1/8	Rear
8	Exhaust	R.H
		EXH
	3

	Service
	Cord		23-7/8
	Entry at
	Bank of		6	74-1/8
	Appliances		1-1/2
46	Standpipe & Faucets		120V
		33" Min.	15 or 20A

Dryer Mounting Position

These instructions explain two mounting positions for your 24 inch dryer.

Installation Procedure:

1Obtain two pieces of 2x4 long enough to span at least two wall studs and the width of the dryer.

2.Locate wall stud center lines. Mark wall stud center lines on two pieces of 2x4 in relationship to position dryer is to be mounted.

3.Referring to dimensional drawing, draw a horizontal reference line (73") from the floor to locate upper 2x4 support.

4.Position, level and secure upper 2x4 with four 1/4 x 3 inch wood screws. The bottom of the 2x4 should be positioned on reference line.

5.Referring to dimensional drawing , draw a horizontal reference line 32" down from the bottom of the upper 2x4 support.

6.Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. The center line of the 2x4 should be positioned on reference line.

7.Referring to figure 1, mount the metal wall bracket 1/8 inch from the bottom of the upper 2x4 support with five 1-1/2 inch wood screws.

8.Referring to figure 2, remove one screw from each lower rear corner of dryer and, using same screws, secure lower brackets (supplied) as shown.

9.Dryer is supplied with exhaust at the top, locate and install outside exhaust duct referring to the dimensional drawing For other optional exhaust directions as shown in dimensional drawing (rear and sides) refer to dryer installation instruction sheet.

10.Position the dryer on the wall mounting bracket and check that the dryer is plumbed.

11.If the dryer needs plumbing, use some of the twelve washers supplied with the kit as spacers behind lower brackets of figure 2 and secure the dryer to the lower 2x4 support using the remaining 1-1/2 inch wood screws

WALL BRACKET

26 28

23-5/8

2 x 4

This kit consists of the following: 1 Wall mounting bracket

2 Bottom Brackets

6-1/4 x 3 inch wood screws

General Information:

The back of the dryer is not accessible for service or maintenance after dryer mounting installation is complete. It is recommended that the dryer be checked and electrical installation completed prior to mounting. For service or maintenance requiring rear access, the dryer must be removed from the wall.

CAUTION: DISCONNECT ELECTRICAL CURRENT BEFORE INSTALLING OR SERVICING DRYER.

1/8 " MAX

Figure 1

REAR VIEW FRONT VIEW

7-1/4 x 1-1/2 inch wood screws 12 washers

Dryer Requirements

Carefully read and follow individual dryer installation instructions for exhausting requirements.

The electrical outlet must be located above the dryer, or beside the dryer if adequate dryer-to-wall clearance is available. The outlet must be within three feet on a 240 volt dryer or a 120 volt dryer from the service cord entry on the rear of the dryer.

Specification Created 10/04

CAUTION

The 120 volt receptacle on the back of the 240 volt dryer must not be used with this wall mount kit.

Figure 2

360440