GE ZIC360N RH Design Guide, to.t width/llg, 2-8/1B, The Installation Space, Im, 13 ,/8

Design Guide

THE INSTALLATION SPACE

35-I/2"

FinishedWidth

.to.t width/llg		2-8/1B''
mustbe	/11	_T	,,
The linished	/	Im :8			Wal,View
	_1
84-1/ maxL10				]]	75" From
83-1/2" min		]L_24" CutoutDepth		]]	of ElectricalArea
	Finished				Floorto Bottom
	Opening	I ] E
	I	115'WaterSupply _
		])¢)	_:: (_
	_'	31/2"	31/2"	'

Water And Electrical Locations

Electrical and water suppl) must be located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slighfl_ bexond

ac!iacent cabinetry, dei)ending, on _our installatilm.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot

exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An indMdual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground tault interrupter) is not

recollllllended.

• Water line can enter the opening through the floor or back wall. The water line should be 1/4"

O.D. copper tubing or GE SlnartConnect ''_ kit

between the cold water line and water connection

location, long enough to extend to the fl'ont of the

refl'igerator. Installation of an easily accessible sh ut-ott wflve in the water line is required.

ZUG2, ZUGSS2 Unified Grille Panel Kit

•If you are installing two reli'igerators, side b_, side,

the installation space must be 71-1/2" wide.

Note:Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width.

•The water and electrical locations fl_r each product mtlst be located as shown.

•A separate l ISV, 60Hz., 15 or 20 amp power supply

is recommended fin" each product.

DIMENSIONS AND CLEARANCES

35"	25-3/4"FramedModels
CaseWidth	25-3/4"StainlessSteelModels
	CaseOept,,
		_ Shippingheight.The
--'_	]	refrigeratorfit into cutoutthatcan be adjustedis
	_'84"From	83-1/2" min.to 84-1/2" max.
_83-1'2"1 _	I Floorto	height. Note that thetop
	TopFrame	casetrim at the front is
		uppercabinetryorsoffit.
		Uselevelinglegs andwheels
		for a maximum1" height
	36_Fr'd	adjustment.
		1/2" higherandwill overlap

" me to

FrameWidth

DepthIncludingHandles:

26-7/8"FramedModels

27-3/4"StainlessSteelModels

Product Clearances

These refrigerators are equipped with a 2-position door stop. The factory set 130 ° door swing can be

a@Bted to 90 ° if clearance to a@_cent cabinets or walls is restricted.

130° Door Swing			90° Door Swing
	Minimum
	to Wall		,		Behind
	,	25"_			]13_,/8,,
					/ Frame
	i
	[,,,
			L_		'[
			(
					!36-3/4"
130°		,		90°	:j
Allow 25"	minimum	clearance	for	a flfll	4" Minimum
					to Wall
130 ° door	swing.	Allow 15" fl_r	pan	remoxal.

4" minimum clearance is required when door swing

is a(!justed to 90 °. If the 90 ° door stop position is

used, pan access is maintained, but pan removal is restricted.

See illustrations pages 4 and 5 to deteHnine door swing

interaction with a@_cent cabinets or countertops.

-_71-1/2"FinishedWidth--

WallView

	_)6"		;	F6"
	10"		10"
84-1/2"max	24"Cutout			75"From
83-1/2"rain	Depttl
				Floorto Bottom
Finished				of ElectricalArea
Opening
			WaterSupply5_
.............................		26"_	_26	"_
	_-/
3-1/2"				3-1/2"

3