GE ZIF36NM - GE Monogram 36 Built-In All-Freezer, Monogram.“, 1/4 Accessory Panels, White

Monogram.“

ZIF36NM – GE Monogram 36" Built-In All-Freezer

1/4" Accessory Panels:

Factory trim accepts accessory panel kits. Panels are cut to size and ready to install. Kits must be ordered separately.

Custom Panels – Match the cabinetry! ZKTR36LH for ZIR36NMLH, ZIF36NMLH ZKTR36RH for ZIR36NMRH, ZIF36NMRH

				Provides for the installation of 3/4" thick custom door and grille
	White	Black	Stainless
				panels. Use this kit for a trimless appearance. This kit provides
Models	Lexan®	Lexan®	Steel
				a standard handle to fit the 3/4" panel.
ZIR36/ZIF36	ZWWR36	ZWBR36	ZWSR36
				Grille Panel – For Installation height adjustments!
Door Handles – To match or complement cabinetry!
				ZGC2 – Provides 1/4" grille panel frame side pieces for 83-1/2"
ZKHR1 – Provides the necessary framework to install a custom
				and 84-1/2" installation heights. The supplied grille panel frame
handle of your choice, onto a 1/4" thick custom panel. (Handle				is set for 84".
not included.)				Side-by-Side Installation
ZKHTR1 – Provides the necessary framework to install a cus-
				ZUG75 Trim Kit – For side-by-side installation of two trimmed
tom handle of your choice, onto a 3/4" thick custom panel.
				units. This kit provides for the
(Handle not included.) This kit must be used in combination with
				installation of a unified 3/4" grille
ZKTR36LH or ZKTR36RH.
				panel to span the width of two
ZKHRSS1 – Tubular stainless steel handle for 1/4" thick panel				units. This kit contains a trim
installation.				strip to cover the inside case
ZKHTRSS1 – Tubular stainless steel handle for 3/4" thick panel				trim for a finished appearance.
installation. This kit must be used in combination with ZKTR36LH				This kit must be used in
or ZKTR36RH.				combination with BOTH the
				ZKTR36LH and ZKTR36RH kits.
• Side panels are required whenever the sides of the				• If you choose to use 1/4" side panels, they should be inserted into
product will be exposed and when		installed between		the case trim as illustrated. Fasten the panels to the product
frameless cabinets.				with stick-on hook and loop fastener strips (not provided) before
• Side panels are not required when installed into				setting in place. See illustration A.
an enclosure.				• 1/2" to 3/4" side panels are normally set into place and fastened
• Side panel installation will be determined by the design				to adjacent cabinetry or the back wall before rolling the product
of the side panel you have previously chosen.				into the opening. See illustration B.
• Side panels must be installed plumb.

Illustration A	23 9/16"
1/4" Side Panels – Insert
end of side panel into case
trim. Fasten with hook and
loop strips.
	84"
Trim
Top View	2 9/16"

Standard 4" high toekick or trim to fit. Height may vary depending on application.

Specification Revised 4/05 110156

Illustration B	24 3/4"
1/2" to 3/4" Side Panels –
Leading edge of side panel
is flush with cabinet front.
Fasten to the back wall
using a cleat.
	84"

3 3/4"

Top View

Standard 4" high toekick or trim to fit.

Height may vary depending on application.

		For answers to your Monogram,® GE Profile™ or
	Listed by	GE appliance questions, visit our website at
	Underwriters	GEAppliances.com or call
R	Laboratories	GE Answer Center® service, 800.626.2000.