GE Monogram JN327 Mark Holes, Cut Holes, Run Wires, B.Outside top exhaust Vertical duct-7″ Round

Installation Instructions

11MARK HOLES

Select the vent option that your installation will require and proceed to that section:

A. Outside top exhaust

(Vertical duct–31⁄4″x 10″ Rectangular)

•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.

Hood mounting screws (4)

133⁄4″ (30″ hood)
	133⁄4″ (30″ hood)
163⁄4″ (36″ hood)	163⁄4″ (36″ hood)
Cabinet front

		73⁄4″
	Cabinet Bottom
	51⁄4″	51⁄4″	11⁄4″	95⁄8″
33⁄4″	Vertical duct
	access hole
	1⁄2″			13⁄8″

		Electrical access hole
Wood shims		(in cabinet bottom)
(recessed-bottom cabinetsCenter
only–shims must be a	line
minimum of 3/8″ thick

and cut to fit the width of the inner recessed cabinet bottom)

B.Outside top exhaust (Vertical duct–7″Round)

•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.

Hood mounting screws (4)

133⁄4″ (30″ hood)		13	3	″	(30	″	hood)
163⁄4″ (36″ hood)				⁄4
	16		3	″	(36	″	hood)
				⁄4

Cabinet front

Cabinet		73⁄4″
bottom	8″ DIA.		9	5	⁄8″
Access		11⁄4″
	HOLE
hole for 7″		53⁄4″
round duct			13⁄8″

Wood shims		Electrical access
	Center	hole (in cabinet bottom)
(recessed-bottom cabinets
	line
only–shims must be a minimum
of 3/8″ thick and cut to fit the
width of the inner recessed
cabinet bottom)

C. Outside rear exhaust

(Horizontal duct–31⁄4″x 10″ Rectangular)

•Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, electrical wiring and keyhole screw slots.

Wood shims

(recessed-bottom cabinets only–shims must be a minimum of 3/8″ thick and cut to fit the width of the inner recessed cabinet bottom)

	Cabinet front		1⁄2″ 11⁄4″
33⁄4″	Horizontal duct
Cabinet	access hole
	51⁄4″	51⁄4″
bottom
133⁄4″ (30″ hood)		73⁄4″
		133⁄4″ (30″ hood)
163⁄4″ (36″ hood)		163⁄4″ (36″ hood)

Hood mounting screws (4) Center line	Electrical access hole
	(in wall)

D. Recirculating (non-vented ductless– JN327 and RN328, and optional on JV347 and JV367 models only)

•Use the hood as a template and mark the locations on the cabinet for the electrical wiring and keyhole screw slots.

•Since the hood is to be recirculated (not to be vented outside), do not cut out any vent openings in the wall or cabinet bottom.

12CUT HOLES

Cut holes at marked locations for duct and electrical wiring. For the vertical duct, cut out 3/4″ extra toward the front of the cabinet so you can move the duct freely when installing the hood. It may also ease installation by cutting the hole 101⁄2″ instead of 10″.

13RUN WIRES

Run the electrical wires through the wall or cabinet according to National Electrical Code and applicable local codes.

NOTE: DO NOT turn the power on until installation is complete.

12