GE Monogram Wine Chiller Wine Reserve and Beverage Center Design Guide, The Installation Space

Models: Wine Chiller Wine Reserve and Beverage Center Wine Reserve and Beverage Center

1 8
Download 8 pages 1.44 Kb
Page 3
Image 3
Design Guide
90° Door Swing

Design Guide

THE INSTALLATION SPACE

 

Locate

 

 

Outlet

 

 

10-1/2" 24"

 

34-1/2"-35"

9" Max.

 

 

1-1/2"

23-3/4"

 

23-3/4" Min.

 

 

PRODUCT CLEARANCES

The wine chiller, wine reserve and beverage center is factory set for a 110° door swing.

When installed in a corner:

Allow 4″ min. clearance on the hinge side for the 90° door swing and to allow racks to slide out.

Allow 10″ minimum clearance on the hinge side for a full 110° door swing.

NOTE:

34-1/2"

Handle and

 

handle standoff

 

depth is 1-3/4

 

23-3/4"

The cutout depth should be 24

The cutout dimensions shown allow for a full door

10" Minimum

to Wall

110°

21-5/8"

23-5/8"

90°

4" Minimum

to Wall

swing and access to the pull-out racks when installed as a built-in in standard 24″ deep cabinets.

The wine chiller, wine reserve and beverage center can be installed freestanding.

If installing between frameless cabinets, a 1/2″ wide filler strip or side panel may be needed on hinge side. The filler strip will act as a spacer between the case and adjacent cabinet door swing. The width

of the opening must include the filler panels. NOTE: The door should protrude 1″ beyond the

surrounding cabinets.

Additional Specifications

A 120 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall as shown. Electrical must be located on rear wall as shown. NOTE: GFI (ground fault interrupter) is not recommended.

The door swing is reversible on all models. If desired, change the door swing before installation.

Choose the location:

These products may be closed in on the top and three sides as long as the front is unobstructed for air circulation and proper access to the door.

Do not install these products where the temperature will go below 55°F (13°C) or above 90°F (32°C).

Do not install where it will be subject to direct sunlight, heat or moisture.

These products are not designed to be stacked one over the other.

Black or Stainless Steel Toekick Options

These products are shipped with a black toekick installed. An optional stainless steel toekick is also supplied with each product. For shipping purposes, the stainless steel toekick is secured to the back

of the unit.

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacity by installing two Monogram

beverage centers, wine chillers or wine reserves together.

 

 

 

 

 

 

 

 

 

 

Locate

 

 

 

 

 

 

 

 

 

 

 

 

Outlet

Or, for a complete refreshment center, install any two

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10-1/2"

 

 

 

14"

 

10-1/2" 24"

of these units together.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• A side-by-side installation requires at least a 47-1/2″

34-1/2"-35"

9"

 

9"

 

 

 

 

 

 

 

wide opening. No trim kits required.

 

 

 

 

15"

 

 

 

 

 

 

 

 

 

 

1-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/2"

 

 

• Products must operate from separate, properly

 

 

 

 

 

 

 

47-1/2" Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

grounded receptacles.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

Page 3
Image 3
GE Monogram Wine Chiller Wine Reserve and Beverage Center Design Guide, The Installation Space, Product Clearances