+/-8% to the pitch control slide. The 16% button will assign +/-16% to the pitch control slide. The PITCH CONTROL (13) must be ON for the 4%, 8% and 16% BUTTONS (12) to work.
PITCH: Pushing the PITCH CONTROL (13) activates the pitch section of the unit (pitch LED glows red). The pitch of the CD will change according to the position of the PITCH CONTROL (13).
PITCH BEND BUTTONS: Pushing the PITCH BEND BUTTONS (14) will automatically raise or lower the pitch +/-4%, 8% and 16% without changing the slide setting. Releasing the buttons will return the pitch to the slide setting. You can use this function to match the pitch bend when mixing from one song to another.
SET CUE: Use the SET CUE (15) button to activate the DIRECT ACCESS BUTTONS to set a CUE POINT. See the CUE INSTRUC- TIONS section for more information.
DIRECT ACCESS BUTTONS: Use the DIRECT ACCESS BUTTONS
(16)to select what track to play and to set a CUE POINT. See the CUE INSTRUCTIONS section for more information.
SINGLE: Pressing the SINGLE (17) button will activate the AUTO CUE FUNCTION and cause the unit to stop at the beginning of music of the following track. This allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track).
CONTINUE: The CONTINUE (18) function will cause the unit to play continuously.
PLAYBACK DISPLAY: The PLAYBACK DISPLAY (19) displays the time remaining to play and flashes slowly when the track has 15 seconds left. The PLAYBACK DISPLAY (19) flashes quickly when the track has 5 seconds left.
DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals into the BNC CONNECTOR (24) on the rear panel of the transports allows you to receive a digital signal from CD.
CUE INSTRUCTIONS
Special Mode for CUE 1 (only):
1.Play the track you wish to play, push pause and move the SEARCH JOG WHEEL (7) to the exact point you wish play to begin, and then PLAY/PAUSE BUTTON (5) to memorize the CUE 1 POINT (CUE 1 LED will blink).
NOTE: When a CUE LED is not lit, there is no CUE POINT saved in memory. When a CUE LED is blinking, the unit is ready for you to change the CUE POINT. When a CUE LED stays lit, there is a CUE POINT saved in memory. To change the saved CUE POINT you have to press this CUE BUTTON (the CUE LED will then blink) and then you can change the CUE POINT.
To set a cue point, follow these instructions:
1.Use the TRACK SKIP (6) to find the track you wish to play. Listen to the track and when the track gets to the approximate spot, push the PLAY/PAUSE BUTTON (5), and if the cue LED is not blinking (indicating the unit is ready for you to set the cue) press the CUE BUTTON you wish to assign the cue to (CUE 1 or CUE 2), than you must touch the SEARCH JOG WHEEL (7) to fine tune the memo- rized cue point, adjusting the CUE POINT forward or backward. The unit will go into CUE MODE (cue LED will be lit) and the location indicated on the display will be the memorized cue point. Push the PLAY/PAUSE BUTTON (5), and the unit will instantly play from the spot selected. If you don’t want to memorize the adjusted CUE POINT, after touching the SEARCH JOG WHEEL (7), push the CUE BUTTON (with the blinking LED) and then the PLAY/PAUSE BUTTON (5). While in play mode, pressing the CUE BUTTON will pause the play and bring you back to the CUE POINT.
2.Press the second CUE BUTTON from PLAY MODE ONLY and repeat the process with the second CUE BUTTON, to set a second
CUE POINT.
3.To preview a CUE POINT, from PLAY MODE press PLAY/PAUSE BUTTON (5), and then press and hold down the CUE BUTTON to preview the CUE. Letting go of the CUE BUTTON will bring you back to the CUE POINT and PAUSE MODE.
AND/OR
To use the SET CUE BUTTON (15) and the DIRECT ACCESS BUTTONS (16) to set a cue point, follow these instructions:
1.Press the SET CUE BUTTON (15) (the LED will light). Use the DIRECT ACCESS BUTTONS (16) to memorize the spot at which you want play to start, the CUE POINT, by selecting the proper track, minute, second and frame. Press CUE 1 to set the cue to CUE 1 (press CUE 2 if you wish to set the cue to CUE 2). You can do this in any mode, including PLAY MODE, so that you may cue a track while playing a track.
TROUBLE SHOOTING
•If THE DISC WILL NOT PLAY, check to see if the disc was loaded correctly (written side up). Also check the disc for excessive dirt, scratches, etc.
•If the disc turns but there is no sound, check the cable connections. If they are okay , check your amplifier or receiver.
•If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip an most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly.
SPECIFICATIONS
GENERAL: | | | |
Type | Dual Mechanism Compact Disc Player w/wired remote |
Disc Type | | Standard Compact discs (12 cm & 8 cm) |
Time Display | Track Elapsed, Track Remain, or Total remain |
Variable Pitch | | ± 4%, ± 8%, ±16% Slider with Resume Switch |
Pitch Bend | | ±4% |
| | | ± 8% |
| | | ± 16% |
Instant Start | | Within 0.03 seconds |
Track Selection | | 1 to 99 Tracks |
Installation | | 19" Rack Mountable Player Unit, 2 U |
| | | 19" Rack Mountable Control Unit, 3 U |
Power Supply | | AC 120/230V, 50/60 Hz |
Power Consumption | 16W |
Dimensions | | Player Unit 19” (W) x 3.5" (H) x 10" (D) |
| | | Control Unit 19” (W) x 5.2" (H) x 2.9" (D) |
Weight | | Player Unit 11.7 lbs (5.3 kg) |
| | | Control Unit 3.8 lbs (1.7 kg) |
AUDIO SECTION: | | |
Quantization | | 1 Bit Linear/Channel, 3 Beam Laser |
Oversampling Rate | 8 Times |
Sampling Frequency | 44.1 kHz |
Frequency Response | 10 Hz to 20 kHz |
Digital Output | | IEC908 |
Total Harmonic Distortion | ..............................................Less Than 0.05% |
Signal to Noise Ratio | 104 dB |
Dynamic Range | | 98 dB |
Channel Separation | 90 dB (1 kHz) |
Output Level | | 1.9 Volts R.M.S. |
*Specifications and design are subject to change without notice for purpose of improvement.
