INTRODUCTION:
Congratulations on your purchase of a
CAUTIONS:
1.Read all operating instructions before using this equipment.
2.To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE
PARTS INSIDE. Please refer servicing to a qualified Gemini Sound Products service technician.
3.Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4.This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5.When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
6.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
CONNECTIONS:
PLEASE NOTE IT IS VERY IMPORTANT THAT YOUR AMPLIFIER HAS MATCHED POWER RAT- INGS!
Make sure your equipment is completely OFF. Lower ALL VOLUME, LEVEL, & GAIN controls before connecting the speaker.
1.Use a 1/4” SPEAKER CABLE from your AMPLIFIER LINE OUTPUT to connect to your speaker’s 1/4” INPUT JACK (1).
2.Another way to connect your AMPLIFIER to your speaker is through the TERMINAL CUP (3). Use the
3.You can also use the 1/4” AUXILIARY OUTPUT JACK (2) to CHAINLINK an additional speaker using a 1/4” SPEAKER CABLE.
OPERATION:
The speakers can be used in pairs for a NORMAL setup, or in groups of four when
NORMAL SETUP:
1.Now turn on your MIXER or other signal source.
2.Then turn on your AMPLIFIER and increase the VOLUME or GAIN control as recommended by the AMPLIFIER’s manual.
3.Start playing from your TURNTABLE, CD PLAYER, MIC, etc. and adjust the volume controls from your mixer to a reasonable level.
Only 1 additional speaker can be added to each speaker in a CHAINLINK setup. Connect your speakers first then follow the steps for a NORMAL setup, your AMPLIFIER should compensate for the extra speakers.
INTRODUCCIÓN:
Felicitaciones en su compra de un sistema del altavoz de la
PRECAUIONES:
1.Deberán leerse todas las instrucciones de operación antes de usar el equipo.
2.Para reducir el riesgo de shock eléctrico, no abra esta unidad. No contiene PIEZAS REEMPLA-
ZABLES POR EL USUARIO. Por favor, refiera el servicio a un técnico de servicio calificado.
No devuelva el aparato a la tienda donde lo compró.
3.No exponga la unidad a la luz solar directa ni a una fuente de calor, por ejemplo, un radiador o estufa.
4.Esta unidad sólo deberá limpiarse con un paño húmedo. Evite el uso de disolventes u otros detergentes de limpieza.
5.Para mover este equipo, colóquelo en la caja y empaque original, a fin de reducir el riesgo de daños durante el transporte.
6.NO DEJE ESTA UNIDAD EXPUESTA A LLUVIA O HUMEDAD.
7.NO USE LIMPIADORES DE ROCÍO O LUBRICANTES EN CUALESQUIER CONTROLES O INTERRUPTORES.
CONEXIONES:
¡NOTA ES POR FAVOR MUY IMPORTANTE QUE SU AMPLIFICADOR HA EMPAREJADO GRADOS DE ENERGÍA!
Se cerciora de su equipo está totalmente APAGADO y también más bajo TODO el VOLUMEN, NIVEL, y CONTROLES del AUMENTO y antes de conectar el altavoz.
1.Utilice un 1/4” SPEAKER CABLE de su línea del AMPLIFIER LINE OUTPUT para conectar con su 1/4” INPUT JACK (1) de los altavoces .
2.Otra manera de conectar su AMPLIFICADOR con su altavoz es la TERMINAL CUP. Utilice los
3.Usted puede también utilizar el
INSTRUCCIONES DE FUNCIONAMIENTO:
Los altavoces se pueden utilizar en los pares para una disposición NORMAL, o en grupos de cua- tro cuando
DISPOSICIÓN NORMAL:
1.Ahora dé vuelta encendido al su MEZCLADOR o a la otra fuente de la señal.
2.Entonces gire su AMPLIFICADOR y aumente el VOLUMEN o GANE el control según lo recomen- dado por el manual del dueño de los AMPLIFICADORES.
3.Comience a jugar de su PLACA GIRATORIA, LECTOR DE CD, MIC, ETC. y ajuste los controles de volumen de su mezclador a un nivel razonable.
Solamente 1 altavoz adicional se puede agregar a cada altavoz en una disposición del ACO- PLAMIENTO de CADENA. Conecte sus altavoces primero entonces siguen los pasos para una disposición NORMAL, su AMPLIFICADOR debe compensar para los altavoces adicionales.