
INTRODUCTION:
Congratulations on your purchase of a
&manufactured by Gemini Sound Products. The new Gemini GX speaker range includes the very latest technology in lightweight ABS design trapezoidal design for a more precise and accurate sound these speakers will add increased sound definition on vocal frequencies. Available as either 10” passive or active units and complete with handles for easy transportation make the new
FEATURES:
100 watts RMS, 250 watts peak power 10" two way loudspeaker
Compression driver with titanium diaphragm Aluminum
Auxiliary line output (for bridging)
Stand mounting sockets for stage monitoring Full metal grill
Rigging points & easy carry handles
100 watts RMS, 250 watts peak power Powered 10" two way loudspeaker Compression driver with titanium diaphragm Aluminum
1/4" & XLR mic/line inputs XLR/RCA line inputs Clip & power LEDs
Stand mounting sockets for stage monitors Aluminum
CAUTIONS:
1.All operating instructions should be read before using this equipment.
2.To reduce the risk of electrical shock, do not open the unit. There are, NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified Gemini Sound Products service technician.
3.Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4.This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents.
5.When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
6.DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7.DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.
LINE VOLTAGE SELECTION:
The GEMINI
230 volts. Be sure to set the proper voltage:
1.Place the head of a screwdriver in the center of the VOLTAGE SELECTOR (24) switch found on the rear panel.
2.Slide the switch to 115 or 230 volts.
3.Do not force or twist the switch. Excessive force may cause damage. If the switch does not move smoothly, contact a qualified technician.
4.Plug in the
5.The fuse is located within the AC INLET (23). When replaceing use a fuse of the same value only.
SET-UP:
Use the provided mounting hardware for a STAGE MONITORING setup.
Slide the plastic legs into the holes on the side of the speaker. Refer to the
CONNECTIONS:
Make sure ALL your equipment is completely OFF and lower ALL VOLUME, LEVEL, & GAIN controls and before connecting the speaker.
1.For the
2.For the
3.You can also use the AUXILIARY LINE OUTPUT JACKS (7, 13, & 14) to
CHAIN-LINK:
When
NOTE: PLEASE REFER TO THE CONNECTIONS GUIDE ON PAGE 5 FOR DETAILED INSTRUCTIONS!
OPERATION:
The speakers can be used in PAIRS for a NORMAL setup, or in groups of FOUR when
GX-200:
1.First turn on your MIXER or other signal source.
2.Then turn on your AMPLIFIER and increase the VOLUME or GAIN control as recommended by the AMPLIFIERS owner manual.
3.Start playing from your TURNTABLE, CD PLAYER, MIC, etc. and adjust the volume controls from your mixer to a reasonable level.
GX-250:
1.First turn on your MIXER/MICROPHONES or other signal source, then turn on your SPEAKER, the POWER LED (22) will be lit. Start playing from your TURNTABLE, CD PLAYER, MIC, etc. and adjust the volume controls from your MIXER/MICROPHONES, to a reasonable level.
2.Use the MIC 1 (15) or LINE IN (16) level controls to adjust MIC 1 (9, 10) or LINE IN (11, 12) levels. The MIC 1/LINE IN LEVEL (15, 16) controls can be used to adjust the level of the LINE OUT (13, 14) signals as well.
3.Use the speakers MASTER (17) level control to adjust the overall level of the SPEAKER, and use the TREBLE (18) & BASS (19) controls to adjust the TREBLE & BASS levels. If your MIC 1 (9,10), LINE 1 level (11, 12) or if the speakers MASTER (17) level is too loud or distorted the CLIP LED (21) will be light up or flash, adjust your volume to a reasonable level.
SPECIFICATIONS:
SEE PAGE 10 FOR SPECIFICATIONS.
SHOULD YOU EXPERIENCE ANY DIFFICULTIES OR PROBLEMS, PLEASE CALL: 1 (732)
(7)