1.Unscrew the outside FADER PLATE SCREWS (B). Do not touch the INSIDE SCREWS (C).
2.Carefully lift the fader and unplug the CABLE (D).
3.Plug the new fader into the cable and place it back in the mixer.
4.Screw the fader to the mixer.
5.KILLING FREQUENCIES: There are two ways to kill frequencies, using the LOW, MID and HIGH KILL SWITCHES (20, 21, 22) and using the LOW, MID and HIGH ROTARY CONTROLS (16, 17, 18). When the selected KILL SWITCH is activated the LED will light and the frequency will be killed. When the selected ROTARY CONTROL is turned all the way to the left, the frequency will be killed. You can also use the ROTARY CONTROLS to boost frequencies up to +12 dB. The normal setting for the ROTARY CONTROLS is zero.
SUGGESTION: You can use the Kill Features on each channel to remove Low, Mid and/or High bands for a smoother mix and mix frequencies from both channels to create special effects.
6.PUNCH IN: The PUNCH IN BUTTON (23) allows you to add a channel’s signal to the mix when the crossfader is set to the opposite channel.
7.PUNCH OUT: The PUNCH OUT BUTTON (24) allows you to remove a channel’s signal from the mix when the crossfader is set to that channel.
SUGGESTION: Keep the crossfader in the center and use the punch in and punch out of both channels together to create scratch type effects.
8.LOOP SECTION: To activate loop, press the LOOP BUTTON (25) and the LOOP LED (26) will light. When the LOOP LED is lit, any device connected to the LOOP OUTPUT (38) and INPUT (37) jacks will be inserted into the signal path.
9.OUTPUT CONTROL SECTION: The level of the AMP OUT (34) is controlled by the MASTER (27) control. The BOOTH (28) control adjusts the level of the BOOTH OUTPUT (35). HINT: The booth OUTPUT is used by some DJs to run monitor speakers in their DJ booth. You can also use it as a second ZONE or AMP output.
NOTE: The RECORD OUT (36) has no level control. The level is set by the channel slides and the gain controls of the selected channel. The tonal qualities are set by the bass, treble and mid controls of that same channel.
10.TALKOVER SECTION: The purpose of the talkover section is to allow the program playing to be muted so that the mic can be heard above the music. The MIC/TALKOVER SWITCH (4) has three settings. When the MIC/TALKOVER SWITCH (4) is in the bottom position, the mic and talkover are both off. When the MIC/TALKOVER SWITCH
(4)is in the center position the mic is on, the MIC INDICATOR (5) will glow, but talkover is off. When the MIC/TALKOVER SWITCH (4) is in the top position, the mic and talkover will be on and the volume of all sources except the Mic input are lowered by 16 dB. The TREBLE (6), BASS (7), and LEVEL (8) controls allow you to fully adjust the mic signal.
11.CUE SECTION: By connecting a set of headphones to the HEADPHONE (9) jack, you can monitor either channel or both. Select the Channel I by sliding the CUE SLIDER (29) control to the left or Channel II by sliding the CUE SLIDER (29) control to the right. Use the CUE LEVEL (30) control to adjust the headphone volume without effecting the overall mix.
12.DISPLAY: The dual function DISPLAY (31) indicates either the MASTER OUTPUT (34) left and right levels or the channel I and channel II levels. You can choose the option you want by pressing the DISPLAY (32) button.
NOTE: When the DISPLAY (31) is in the channel I/channel II display mode, by adjusting the individual channel gain and tone controls, you can increase or decrease the signal to match the other channel’s signal. The channel slides and crossfader have no effect on the display readings.
Specifications
INPUTS: |
|
DJ Mic | 1.5mV 2Kohm balanced |
Phono | 3mV 47Kohm |
Line | 150 mV 27Kohm |
OUTPUTS: |
|
Amp/Booth | 0 dB 1V 400ohm |
Max | 24V Peak to Peak |
Rec | 225mV 5Kohm |
MIC: |
|
Bass | ± 12dB |
High | ± 12dB |
GENERAL: |
|
Bass (Channels I - II) | + 12dB/Kill |
Mid (Channels I - II) | + 12dB/Kill |
Treble (Channels I - II) | + 12dB/Kill |
Gain (Channels I - II) | 0 to |
Frequency Response | 20Hz - 20KHz +/- 2dB |
Distortion | 0.02% |
S/N Ratio | better than 80dB |
Talkover Attenuation | |
Headphone Impedance | 16ohm |
Power Source | 115/230V 50/60Hz 10W |
Dimensions | 10”w x 4 5/8”h x 14”d |
Weight | 8.3 lbs. |
Page 4
