Gemini MM-01 4U 19 manual Specifications, Inputs, Outputs, General

9.CROSSFADER SECTION: The CROSSFADER (38) allows you to mix from one source to another. The CH 2

(28)is controlled on the LEFT side of the CROSSFADER

(38).CH 3 (31) is controlled by the RIGHT side of the CROSSFADER (38). CH 1 (25) and CH 4 (34) are con- trolled through their respective SLIDE CONTROLS (25, 34) and not the CROSSFADER (38). The CROSSFADER

(38)in your unit is removable and if the need arises can be easily replaced. Your Gemini mixer comes with an RG- 45 PRO (RAILGLIDE™) Dual-Rail Crossfader. Rail Glide™ crossfaders have internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end. Also available is our CF-45 PRO (PROGLIDE™) Dual-Rail Crossfader. This unique crossfader features, state of the art conductive plastic technology, for unlimited useage. Another crossfader we have available is the PSF-45 (PRO SCRATCH™) cross- fader with a special curve designed for scratch mixing. Just purchase one from your Gemini dealer and follow the instructions:

Replaceable Crossfader

1.Unscrew the outside FADER plate screws (B). - Do not touch INSIDE SCREWS (C).

2.Carefully remove old

Crossfader and unplug CABLE (D).

3.Plug new Crossfader into CABLE (D) and place back into mixer.

4.Screw Crossfader to mixer with the FADER PLATE SCREWS (B).

10.MIC SECTION: Plug your main mic into the MIC 1 XLR INPUT (15) located on the top panel. The rotary controls for HIGH (18) and LOW (19) for MIC 1 (15) allow you to adjust the tone of MIC 1 (15). The MIC 1 ROTARY VOL- UME CONTROL (17) above the HIGH(18)/LOW(19) con- trols adjust the decibel level of MIC 1 (15). You may also plug a second mic into the rear panel at the MIC 2 ¼" JACK (14). The tone and decibel level of MIC 2 (14) is controlled by the CH 1 SLIDE (25) and the 5 BAND EQ (35).

11.TALKOVER: The purpose of the TALKOVER MODE is to allow the program playing to be muted so that the mic may be heard above the music. The MIC/TALKOVER SWITCH (16) controls MIC 1 (15) with 3 settings:

- When the MIC/TALKOVER SWITCH (16) is in the BOT- TOM position, MIC 1 (15) and TALKOVER MODE are all OFF.

- When the MIC/TALKOVER SWITCH (16) is in the CEN- TER position, MIC 1 (15) is ON and TALKOVER MODE is OFF. The MIC ON LED INDICATOR glows when MIC 1 (15) is ON.

-When the MIC/TALKOVER SWITCH (16) is in the TOP position, MIC 1 (15) is ON and TALKOVER MODE is ON, and the volume of all sources except MIC 1(15) inputs is lowered by -16 dB.

12.VU METER: The VU METER (37) indicates the pro- gram output level of the MASTER (2) left and right stereo levels.

SPECIFICATIONS:

INPUTS:

MIC 1	1.5mV 1kOhm Balanced
MIC 2	1.5mV 1KOhm Balanced
Phono	3 mV 47kOhm
Line	150 mV 10kOhm

OUTPUTS:

Amp	............................................................0 dB 1V 400Ohm
Max	20V Peak to Peak
Rec	225mV 5kOhm

GENERAL:

5 Band EQ	± 12dB
Frequency Response	20Hz - 20KHz +/- 2dB
Distortion	Less Than 0.02%
S/N Ratio	Better Than 80dB
Talkover Attenuation	-16dB
Power Source	Adapter-115V/15V AC 0.5A
................................................................	230V/15V AC 0.5A
Unit Dimensions	W 19" x H 3.4" x D 7"
...............................................................	(483 x 76 x 178mm)
Weight	7.04 lbs (3.19 kg)

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION FOR IMPROVEMENT.

(5)