Genelec 2029A manual System Specifications

Figure 9:	The effect of 'treble tilt', 'bass tilt' and 'bass roll-off' controls in free field.	Figure 10: Horizontal directivity characteristics and power response of 2029A Digital
		in its vertical configuration measured at 1m in free field.

SYSTEM

SPECIFICATIONS

Lower cut-off frequency, -3	dB:	< 68 Hz
Upper cut-off frequency, -3	dB:	> 20 kHz

Free field frequency response of system:

70 Hz - 18 kHz (± 2.5 dB)

Maximum short term sine wave acoustic output on axis in half space, averaged from100 Hz to 3 kHz:

@1m > 100 dB SPL

@0.5m > 106 dB SPL

Maximum long term RMS acousticoutput in same conditions with IECweighted noise (limited by driver unit protection circuit):

@1m > 98 dB SPL

@0.5m > 104 dB SPL

Maximum peak acoustic output per pair on top of console,

@1 m from the engineer with music material:

>110 dB

Self generated noise level in free field @ 1m on axis:

		< 10 dB		(A-weighted)
Harmonic distortion at 85 dB SPL @ 1m on axis:
	Freq:	75...150 Hz		< 3%
		> 150 Hz		< 1%
Drivers:	Bass	130 mm	(5") cone
	Treble	19 mm	(3/ ") metal dome
			4
	Both drivers are magnetically shielded.
Weight:		5.7 Kg		(12.5 lb)
Dimensions:
	Height	247 mm		(9 3/ ")
				4
	Width	151 mm		( 515/16")
	Depth	191 mm		(7 1/ ")
				2

Genelec Oy, Olvitie 5

FIN - 74100 IISALMI, FINLAND

Phone: +358 - 17 - 83881

Telefax: +358 - 17 - 812267

Web: http://www.genelec.com

E-mail: genelec@genelec.com

CROSSOVER

SECTION

Inputs:

Input 1: XLR female, balanced 10 kOhm

Input 2: 1/4 " Jack socket, balanced 10 kOhm

Volume control:

Variable from Mute to -6 dBu for 100 dB SPL output @ 1m

Subsonic filter below 68 Hz :

18 dB/octave

1091A Subwoofer output (input 2) at 100db SPL: -23 dBu into 33kOhm load

Ultrasonic filter above 25 kHz: 12 dB/octave

Crossover frequency, Bass/Treble: 3.3 kHz

Crossover acoustical slopes: 24 - 32 dB/octave

Treble tilt control operating range:

0 to -2 dB @ 15 kHz

Bass roll-off control operating in a -6 dB step @ 85 Hz (to be used in conjunction with the 1091A subwoofer)

Bass tilt control operating range in -2 dB steps: 0 to -6 dB @ 150 Hz

The 'CAL' position is with all tone controls set to 'off' and the input sensitivity control to maximum (fully clockwise).

DIGITAL

SECTION

Word length:	24 bits
Input format:	IEC958, S/P-DIF, EIJAC CP-340
Input termination impedance:		75 ohms
Input sampling rate:	25-55 kHz (no de-emphasis)
	44.1 and 48 kHz (using
	de-emphasis)
Jitter resiliance:	0.15 unit intervals
Dynamic range:	>101 dB (A weight, triangular
	PDF dither, 20 bit data)
De-emphasis:	50/15us, automatic
Recovered clock jitter:	200 picoseconds RMS typical

AMPLIFIER

SECTION

Bass amplifier output power with an 8 Ohm load: 40 W

Treble amplifier output power with an 8 Ohm load: 40 W

Long term output power is limited by driver unit protection circuitry.

Amplifier system distortion at
nominal output:
	THD	< 0.08%
	SMPTE-IM	< 0.08%
	CCIF-IM	< 0.08%
	DIM 100	< 0.08%
Signal to Noise ratio, referred to full output:
	Bass	> 90 dB
	Treble	> 90 dB
Mains voltage:	100/200 or 115/230 V
Voltage operating range:		±10%
Power consumption:
	Idle	9 VA
	Full output	90 VA

Genelec document DR29101

COPYRIGHT GENELEC OY 1998 All data subject to change without prior notice