Generac 5982R Stopping The Engine, Maintenance Schedule, Product Specifications, 3.2.2

Models: 5982R 005982-0

1 20
Download 20 pages 29.62 Kb
Page 11
Image 11
Figure 11 - Engine Controls

Turn engine ON/OFF switch to ON position (Figure 11).

Move engine CHOKE lever to the FULL CHOKE position (Figure 11).

To start engine, firmly grasp the recoil handle and pull slowly until increased resistance is felt. Pull rapidly up and away.

When engine starts, move choke lever to 1/2-CHOKE position until engine runs smoothly and then fully into RUN position. If engine falters, move choke back out to 1/2-CHOKE position until engine runs smoothly and then to RUN position.

NOTICE:

If engine fires, but does not continue to run, move choke lever to the START position and repeat starting instructions.

Figure 11 - Engine Controls

2.8 STOPPING THE ENGINE

Shut off all loads, then unplug the electrical loads from generator panel receptacles. Never start or stop the engine with electrical devices plugged in and turned on.

Let engine run at no-load for several minutes to stabilize the internal temperatures of engine and generator.

Move ON/OFF switch to OFF position.

Close fuel valve.

2.9 LOW OIL LEVEL SHUTDOWN SYSTEM

The engine is equipped with a low oil level sensor that shuts down the engine automatically when the oil level drops below a specified level. If the engine shuts down by itself and the fuel tank has enough gasoline, check engine oil level.

Maintenance

2.9.1 SENSING LOW OIL LEVEL

If the system senses a low oil level during operation, the engine shuts down. The engine will not run until the oil has been refilled to the proper level.

3.1 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required when operating in adverse conditions noted below.

Check Oil Level

At Each Use

Change Oil ¥

*Every 50

Hours

Check Valve Clearance

***Every Season

Service Air Filter

**Every 25

Hours

Replace Spark Plug

****Every 100

Hours

¥Change oil after first 20 hours of operation.

*Change oil every month when operating under heavy load or in high temperatures.

**Clean more often under dirty or dusty operating conditions. Replace air filter parts if they cannot be adequately cleaned.

***Check valve clearance and adjust if necessary after first 50 hours of operation and every 100 hours thereafter.

****Clean and re-gap spark plug every 50 hours.

3.2 PRODUCT SPECIFICATIONS

3.2.1 GENERATOR SPECIFICATIONS

Rated. Power

3.25 kW**

Surge Power

3.75 kW

Rated AC Voltage

120/240

Rated Current

27/13.5 Amps**

Rated Frequency

60 Hz @ 3600 RPM

Phase

Single Phase

**Maximum wattage is subject to, and limited by, such factors as fuel Btu content, ambient temperature, altitude, engine condition, etc.. Maximum power decreases about 3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 6° C (10° F) above 16° C (60° F) ambient temperature.

3.2.2

ENGINE SPECIFICATIONS

Displacement

208 cc

Spark Plug Type

F6TC, NGK BP6IS or Champion RN11YC

Spark Plug Gap

0.030 inch or (0.76 mm)

Gasoline Capacity

13.25 L (3.5 U.S. gallons)

Oil Type

....... See Chart in "Before Starting the Generator" Section

Oil Capacity

0.6 L (0.634 Qts.)

Run Time

9.7 Hours at 1/2 Load

Class II Emission Certified*

*The engine manufacturer must warrant the emission control system for a period of two years. This warranty coverage is in addition to the warranty provided by Generac, and may cover the engine even if Generac’s warranty does not.

9

Page 11
Image 11
Generac 5982R Stopping The Engine, Maintenance Schedule, Product Specifications, Low Oil Level Shutdown System, 3.2.2