Generac 005982-0, 5982R owner manual General Information, Unpacking, Assembly, Know the Generator

General Information

1.1 UNPACKING

•Remove all packaging material.

•Remove separate accessory box.

•Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an authorized dealer at 1-888-436-3722.

•	1	- Owner’s manual
•	1	- Oil SAE 30
•	3	- Product Registration Cards (English, Spanish, French)
• 2		- 8” WHEELS
•	1	- Axle
•	1	- Frame Foot
•	1	- Handle with grip
• 1		- Hardware Bag

Figure 1 – Wheel Assembly

Figure 2 – Handle Kit

1	- Plastic Spacer	2	- M8-1.25 x 40 Bolts
1	- Handle Bracket	1	- M6-1.0 x 40 Bolt
2	- Rubber Bumpers	2	- M8-1.25 x 16 Bolts
2	- Cotter Pins	1	- M6-1.0 Hex Flange Nut
2	- M8-1.25 Hex Flange Nuts

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If problems arise when assembling the generator, please call the Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE ACCESSORY KIT

1x HANDLE BRACKET

1x M6-1.0X40 BOLT

1x PLASTIC SPACER

1x HANDLE W/GRIP

M8-1.25 x 40

BOLTS

1 X M6-10 HEX FLANGE NUT

The wheels are designed to the unit to greatly improve the portability of the generator.

NOTICE:

The wheels are not intended for over-the-road-use.

1.Refer to Figure 1 to install the wheels as shown.

•Slide the axle through the frame brackets.

•Slide on the wheels then install the cotter pins.

2.Refer to Figure 1 to install the wheel bumpers as shown.

•Secure the two rubber bumpers to the frame foot using two M8-1.25 Hex Flange Nuts (if not already assembled).

•Place the frame foot under the frame and secure with two M8-1.25 x 16 bolts.

3.Refer to Figure 2 to install the handle assembly as shown.

•Install the handle bracket to the frame using two M8-1.25 x 40 bolts (if not already assembled).

•Slide the plastic spacer onto the handle assembly then align with the holes in the handle bracket (if not already assembled).

•Secure the handle assembly to the handle bracket using the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating this generator.

Compare the generator to Figures 3 through 6 to become familiarized with the locations of various controls and adjustments. Save this manual for future reference.

1.120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical power for the operation of 120 Volt AC, 20 Amp, single-phase, 60 Hz electrical lighting, appliance, tool and motor loads.

2.120/240V AC, 20 Amp Locking Receptacle – Supplies electrical power for the operation of 120 and/or 240 volt AC, 20 amp, single-phase, 60 Hz, electrical lighting, appliance, tool and motor loads.

3.Circuit Breakers (AC) – Each receptacle is provided with a 2-pole, 14 amp circuit breaker to protect the generator against electrical overload.

4.Air Filter – Filters intake air as it is drawn into the engine.

5.Choke Knob – Used when starting a cold engine.

6.Fuel Tank – Tank holds 4 U.S. gallons of fuel.

7.Grounding Lug – Ground the generator to an approved earth ground here. See "Grounding the Generator" for details.

8.On/OFF Switch – Controls the operation of the generator.

4