START-UP Checklist

Standby Generator Sets

Installation

•Battery charger connection to 120 VAC.

•Communication wires connected between transfer switch and generator (HTS only).

•Unit secured to pad.

Before working on the generator, ensure the fol- lowing:

•The AUTO/OFF/MANUAL switch is in the OFF position.

•The 120VAC supply to the battery charger is switched OFF.

PREPARATION FOR START-UP

•Ensure that the 120VAC circuit breaker to the bat- tery charger is open.

•Remove the fuse from the the control panel. Open the front door of the control box and remove the 15 Amp ATO fuse in the lower left-hand corner of the control box.

•Connect the battery cables to the battery. Attach negative battery cable last.

•Close the 120VAC circuit breaker to the battery charger.

•Measure the voltage at the battery before and after the charger is turned on.

•Verify all AC electrical connections are tight at the circuit breaker and transfer switch.

•Visually inspect entire area looking for loose paper, plastic wrappings, leaves, etc.

•Check all hoses clamps fittings for leaks or dam- age.

•Check all electrical plugs throughout the genera- tor. Ensure each plug is seated correctly and fully inserted into its receptacle.

•Verify the AUTO/OFF/MANUAL switch is in OFF position.

•Open the valve to the engine fuel line.

•Bleed the fuel system of air. (necessary for long fuel lines).

•Open the generator main line circuit breaker.

•Connect a manometer to the gas line and record the static pressure. It must be as listed in the Specifications.

•Insert the fuse into the control panel.

•Move the AUTO/OFF/MANUAL switch to the man- ual position. The engine should now crank and start.

•Check voltage at the generator terminals.

•For 3-phase units, check phase rotation at the transfer switch terminals. The generator phase rotation must match the utility phase rotation.

•Check for coolant, fuel, oil, and exhaust leaks.

•Close the generators main line circuit breaker.

•Turn the generator set off.

•Connect the UTILITY supply to the transfer switch.

•Set the AUTO/OFF/MANUAL switch to AUTO.

•Disconnect utility power before the transfer switch.

Engine should start, transfer to load.

Run at least 15 minutes on generator power. Make certain all 3-phase loads are functioning correctly (correct phase rotation).

•Reconnect Utility power

Transfer switch will transfer back to Utility and engine will shut down within the given time parameters set up for the specific transfer switch and controller.

•Install all covers, access plates and door panels.

•Put the Owners Manual in a safe and accessible place.

•Make certain the AUTO/OFF/MANUAL switch is in the AUTO position.

01/07 C .Rev Install002

8-2

25, 30, 20 specifications

Generac Power Systems is a leading manufacturer of backup power generation products and tools, known for their reliability and innovation. Among their diverse lineup are the Generac 20kW, 25kW, and 30kW home standby generators. These models are designed to provide seamless power during an outage, allowing homeowners to maintain their everyday activities without interruption.

The Generac 20kW generator is particularly popular for residential use. It can power essential circuits as well as larger appliances, making it an ideal choice for homes with moderate electricity needs. One of its standout features is the Smart Management Module, which allows homeowners to manage energy consumption effectively, ensuring that they can run necessary appliances without overwhelming the system. Additionally, the 20kW generator is equipped with a durable enclosure, offering long-lasting protection against the elements.

Moving up in capacity, the Generac 25kW model caters to homes with higher electricity demands. This generator combines efficiency with strength, providing enough power for a wider range of home appliances and systems. It features a TruePower Technology that delivers clean power, crucial for sensitive electronics. Moreover, the 25kW model operates quietly, contributing to a comfortable home environment even during power outages.

The Generac 30kW generator is designed for larger homes or light commercial applications. It provides an impressive power output while maintaining high efficiency. Its features include advanced digital control, allowing for easy monitoring and maintenance. The 30kW model also offers an automatic transfer switch, which ensures that power is restored quickly and safely when utilities fail.

All three models utilize Generac's G-Force engine, known for its low maintenance requirements and high performance. They come with a five-year limited warranty, providing peace of mind for users. Furthermore, with Wi-Fi monitoring capabilities, homeowners can keep track of their generator's status from anywhere, ensuring they are always prepared for any power interruption.

In summary, the Generac 20kW, 25kW, and 30kW generators are excellent options for homeowners seeking reliable backup power. Their advanced features, durable construction, and efficient operation make them stand out in the market. Whether for essential home use or larger applications, Generac's lineup delivers dependable performance and innovative technology.

Generac Power Systems 25, 20, 30 owner manual START-UP Checklist, Preparation for START-UP

Models: 25 30 20