Section 1.6

CONTROL PANEL

CONSTRUCTION
The panel is constructed of sheet metal and includes
a panel box, a panel back cover and a front control
panel. The panel box is retained to an engine-genera-
tor divider plate by five M5 screws. Removal of these
screws will permit the panel to be removed from the
divider plate and set out of the way with connecting
wires still attached. This will allow access to compo-
nents housed in the control panel.
COMPONENTS
A heat sink bracket is attached to the engine-genera-
tor divider plate, for attachment of a heat sink to
which four diode assemblies are mounted. See Items
26 and 31 in the Exploded View of Control Panel.
Other components are also shown in the Exploded
View. Many of these components are part of the
"ENGINE ELECTRICAL SYSTEM" (Part 6 of this
manual).
Page 1.6-1

Figure 1. Exploded View of Control Panel

ITEM QTY. DESCRIPTION
1 9 M50.8 x 12MM PHILLIPS PAN HD.MACH. SCR.
2 1 BOX, CONTROL TOP
3 1 BOX, CONTROL PANEL
4 1 #1032 x 1" PHILLIPS PAN HD. MACH. SCR.
5 1 #1032 HEX NUT
6 8 TAPTITE M5.8 x 10MM
7 1 SNAP BUSHING
8 1 CONNECTOR
10 1 CIRCUIT BREAKER,10A.
11 2 LOCK WASHERM6
12 1 IGNITION MODULE
13 10 LOCK WASHERM5
14 2 POP RIVET.156D
15 2 HEX NUT M6
16 1 ASSEMBLY, COIL
17 2 SPACER, IGNITION COIL MOUNT
18 4 M4 FLAT WASHER
19 8 M5 FLAT WASHER
20 1 CONTROL PANEL, FRONT
21 1 SNAP BUSHING
22 1 SWITCH, SPDT ROCKER
23 1 SWITCH, SPST MOM ROCKER
24 1 FUSE, 15A. AGC
25 1 FUSE HOLDER
26 1 EXTRUSION, CONTROLLER
27 1 RECTIFIER, BATTERY CHARGE
28 4 LOCK WASHERM4
30 1 PANEL DECAL
31 4 DIODE, DUAL 30A
32 1 ASSEMBLY, PCB A6060
33 2 PHMS M30.5 x 10
34 2 LOCK WASHERM3
35 1 RESISTOR, POWER 1 OHM
ITEM QTY. DESCRIPTION
36 2 BUS BAR, OUTER
37 4 TAPTITE M61 x 10MM
38 1 BRACKET, HEAT SINKPCB
40 2 HEX NUT M5
41 1 TERMINAL BLOCK
43 4 BUS BAR, INNER
44 1 GROUND WIRE
45 1 CUSTOMER WIRE HARNESS
46 1 REMOTE PANEL HARNESS
47 1 SNAP BUSHING
48 2 CLAMP, CONTROL PANEL HARNESS
49 1 HARNESS, CONTROL PANEL (NOT SHOWNFOR CLARITY)
50 4 #632 x 1/4" PHILLIPS ROUND HD. MACH. SCREW
51 5 RUBBER UCHANNEL
52 4 M40.7 x 10MM HEX HEAD CAPSCREW
53 1 HOUR METER
54 2 #440 x 3/8" LG ROUND HD
55 2 #4 LOCKWASHER
56 2 #440 HEX NUT
57 4 PPHMS 1032 x 3/8" LG
58 1 BUS BAR, CENTER
59 1 BLACK TIE WRAP, 7" LG
60 4 SHAKEPROOF EXT. #10
61 1 INVERTER ASSEMBLY
62 1 WIRE HARNESS, 7 CONDUCTOR
63 1 WIRE HARNESS, 2 CONDUCTOR
64 1 WIRE HARNESSHEATSINK TO PCBI
65 1 HARNESSPCBI TO PANEL
66 1 HARNESS - HEATSINK TO TERM. BLOCK
67 1 TERMINAL BLOCK, 4 POSITION
68 2 POP RIVET
69 2 M3.05 NUT