Manuals / Gigabyte / Computer Equipment / Computer Hardware

Gigabyte GA-K8NE user manual On-Chip MAC Lan, NV IDE/SATA RAID function, IDE Primary Master RAID

Models: GA-K8NE

1 80

Download 80 pages 12.92 Kb

Page 35

On-Chip MAC Lan

Auto	Auto-detect onboard LAN chip function. (Default value)
Disabled	Disable onboard LAN chip function.

NV IDE/SATA RAID function

Enabled	Enable NV IDE/SATA RAID function. (Default value)
Disabled	Disable this function.

IDE Primary Master RAID

Enabled	Enable 1st master channel IDE RAID function.
Disabled	Disable this function. (Default value)

IDE Primary Slave RAID

Enabled	Enable 1st slave channel IDE RAID function.
Disabled	Disable this function. (Default value)

IDE Secndry Master RAID

Enabled	Enable 2nd master channel IDE RAID function.
Disabled	Disable this function. (Default value)

IDE Secndry Slave RAID

Enabled	Enable 2nd slave channel IDE RAID function.
Disabled	Disable this function. (Default value)

NV Serial-ATA 1

Enabled	Enable Serial ATA 1 supported. (Default value)
Disabled	Disable Serial ATA 1 supported.

NV SATA 1 Primary RAID

Enabled	Enable 1st SATA primary RAID function.
Disabled	Disable this function. (Default value)

NV SATA 1 Secondary RAID

Enabled	Enable 1st SATA secondary RAID function.
Disabled	Disable this function. (Default value)

NV Serial-ATA 2

Enabled	Enable Serial ATA 2 supported. (Default value)
Disabled	Disable Serial ATA 2 supported.

NV SATA 2 Primary RAID

Enabled	Enable 2nd SATA primary RAID function.
Disabled	Disable this function. (Default value)

NV SATA 2 Secondary RAID

Enabled	Enable 2nd SATA secondary RAID function.
Disabled	Disable this function. (Default value)

IDE Prefetch Mode

Enabled	Enable IDE Prefetch mode. (Default value)
Disabled	Disable IDE Prefetch mode.

English

- 35 -

BIOS Setup

Image 35

Gigabyte GA-K8NE user manual On-Chip MAC Lan, NV IDE/SATA RAID function, IDE Primary Master RAID, IDE Primary Slave RAID

Contents

GA-K8NE Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8NE Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyALC850 Codec UAJ Feature SummaryUse of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of MemoryDDR1 DDR2 DDR3 Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII01 / SATAII23 Serial ATA Connector IDE1 / IDE2 IDE ConnectorFpanel Front Panel Jumper Pwrled Faudio Front Audio Panel ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector Cdin CD In ConnectorCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BAT BatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1b „ Exit Without Saving „ Set Supervisor Password„ Set User Password „ Save & Exit SetupIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master, Slave, IDE Channel 1 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B Boot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckOn-Chip IDE Channel1 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel0IDE Primary Master RAID IDE Prefetch ModeOn-Chip MAC Lan NV IDE/SATA RAID functionAC97 Audio Parallel Port ModeECP Mode Use DMA USB Memory TypeModem Ring On Legacy DOS USB MouseLegacy USB Storage detect PME Event Wake UpKB Power on Function Power-On by AlarmPower On By Mouse Power On By KeyboardPnP/PCI Configurations DDR25V PC Health StatusCase Opened Reset Case Open StatusCurrent CPU Temperature CPU Warning TemperatureTemp Limit of High Speed Default temperature 60oC Temp of FAN turn off Default temperature 0oCTemp Limit of Low Speed Default temperature 20oC Temp Limit of Mid Speed Default temperature 50oCPcie Clock CPU FrequencyK8 CPU Clock Ratio CPU Spread SpectrumTop Performance Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? English F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionEntering the RAID Bios Setup Configuring the Nvidia RAID BiosAssigning the Disks Using the Define a New Array WindowSelecting the RAID Mode Selecting the Striping Block SizeYES Completing the RAID Bios SetupArray 2 Nvidia Mirror 76.33G Cd bootdrv Menu Installing the RAID drivers5 2- / 4- / 6- / 8- Channel Audio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step AMI Bios Beep Codes TroubleshootingEnglish English English Taiwan Headquarters Contact UsChina Shanghai