Gitzo PERS-2400 NOTE: ALL TRANSMITTERS WILL BE ERASED, INSTALLING TRANSMITTERS (FROM FRONT PANEL), INSTALLING TRANSMITTERS (FROM INSIDE CONSOLE), TESTING TRANSMITTERS, CONSOLE

INSTALLING TRANSMITTERS (FROM FRONT PANEL)

ADDS ONE TRANSMITTER AT A TIME

INSTALLING TRANSMITTERS (FROM INSIDE CONSOLE)

ADDS MULTIPLE TRANSMITTERS

TESTING TRANSMITTERS

1 PRESS TEST BUTTON

1PRESS CLEAR BUTTON FOR 5 SECONDS5 BEEPS SOUND (TX ADD MODE)2ACTIVATE TRANSMITTER 1 BEEP SOUNDS(TX ADDED) CONSOLE REVERTS TO OPERATE MODE3REPEAT STEPS 1 & 2FOR ADITIONAL TRANSMITTERS (UP TO 16 TOTAL)NOTE: IF THE CONSOLE'S MEMORYIS FULL, ONE LONG BEEP SOUNDS WHEN TRYING TO ADD A TRANSMITTERNOTE: PRESS CLEAR BEFORETRANSMITTING TO RETURN

TO OPERATE MODE WITHOUT ENTERING A TRANSMITTER (2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED, 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED) THE CONSOLE WILL RESUME OPERATE MODE AUTOMATICALLY AFTER

30 SECONDS

NOTE: FOR ALL TWO-BUTTON TX'S EXCEPT DXS-63

INSTALL	INSTALL
WITH	WITH
LEFT	RIGHT
BUTTON	BUTTON
ACTIVATE	ACTIVATE
WITH	WITH
EITHER	BOTH
BUTTON	BUTTONS
NOTE: FOR DXS-31 STATIONARY TRANSMITTERS
INSTALL WITH	INSTALL WITH
JUMPER SET	JUMPER SET
FOR DELAY	FOR INSTANT
ACTIVATES	ACTIVATES
AS EMERGENCY	AS ACTIVITY

DXS-32: CUT JUMPER (INSTANT TX) FOR USE AS AN ACTIVITY TX. SEE DXS-32 INSTALLATION INSTRUCTIONS

1PRESS TEST BUTTON 4 BEEPS SOUND (TEST MODE)2 PRESS TEST BUTTON AGAIN 5 BEEPS SOUND (TX ADD MODE)3ACTIVATE TRANSMITTER1 BEEP SOUNDS (TX ADDED)NOTE: IF THE CONSOLE'S MEMORYIS FULL, ONE LONG BEEP SOUNDSWHEN TRYING TO ADD A TRANSMITTER4REPEAT STEPS 2 & 3 FOR ADDITIONAL TRANSMITTERS (UP TO 16 TOTAL)5PRESS CLEAR TO RETURN

TO OPERATE MODE (2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED, 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED) OTHERWISE, THE CONSOLE WILL RESUME OPERATE MODE AUTOMATICALLY AFTER 3 MINUTES

4 BEEPS SOUND

(TEST MODE)

2ACTIVATE EACH OF THE CONSOLE'S TRANSMITTERS,

ONE AT A TIME

3COUNT THE NUMBER

OF BEEPS THAT THE

CONSOLE SOUNDS

WHEN THE TRANSMITTER

IS ACTIVATED

1-BEEP = TX OK

2-BEEPS = TX HAD ALARM

3-BEEPS = TX MISSED STATUS

4-BEEPS = TX HAS LOW BATTERY

NOTE: WITH THE MODEL VB-4 VOICE BOARDINSTALLED, THE CONSOLE WILL ANNOUNCETHE TRANSMITTER STATUS

4PRESS CLEAR TO RETURN TO OPERATE MODE (2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED,

3 BEEPS SOUNDS WITH ACTIVITY TIMER

DISABLED) OTHERWISE, THE CONSOLE WILL RESUME OPERATE MODE AUTOMATICALLY AFTER 3 MINUTES

ERASING TRANSMITTERS

CONNECTING TO RA-2400 FOR LOCAL CABLE PROGRAMMING

TELEPHONE CONNECTIONS

NOTE: ALL TRANSMITTERS WILL BE ERASED!

1PRESS AND HOLD TEST BUTTON FOR 5 SECONDS 6 BEEPS SOUND(ALL TRANSMITTERS WERE ERASED)

2PRESS CLEAR TO RETURN TO OPERATE MODE (2 BEEPS SOUND WITH ACTIVITY TIMER ENABLED, 3 BEEPS SOUND WITH ACTIVITY TIMER DISABLED) THE CONSOLE WILL RESUME OPERATE MODE AUTOMATICALLY AFTER 3 MINUTES

1PERFORM THE STEPS DETAILED IN THE RA-2400/PERS-2400 REFERENCE GUIDE (P/N 217163) TO SET UP THE RA-2400 PROGRAM

2TO LOCALLY PROGRAM THE CONSOLE, CONNECT

THE MODEM'S LINE JACK

TO THE CONSOLE'S LINE

JACK LINE-TO-LINE

3PRESS TEST BUTTON MOMENTARILY, 4 BEEPS SOUND (TEST MODE)NOTE: CONSOLE WILL EXIT TEST MODEAUTOMATICALLY AFTER 3 MINUTESOR BY PRESSING THE CLEAR BUTTON

4WHEN RA-2400 CONNECTION TIMER STARTS COUNTING DOWN, PRESS THE EMERGENCY BUTTON

4 BEEPS SOUND (RA-2400 ANSWER)

5 PERFORM PROGRAMMING IN THE RA-2400 SOFTWARE, THEN DISCONNECT FROM THE CONSOLE

TELEPHONEJACKLOCAL

TELEPHONE

CONNECT LOCALTELEPHONE TOTHIS JACK

ROUTE CABLES UNDER STRAIN-RELIEF TABSPERS-2400CONSOLE WITHREAR COVERINSTALLEDCONNECT TELEPHONE LINE TO THIS JACK

SYSTEM OPERATION

CONSOLESTANDING BYPOWER LIGHT IS ON OTHER LIGHTS ARE OFF

SUPERVISORY CONDITIONS

TRANSMITTER LOW BATTERY TROUBLE

WHEN A TRANSMITTER SENDS A LOW BATTERY SIGNAL THE
CONSOLE'S TROUBLE INDICATOR WILL BLINK SLOWLY.	WHEN TROUBLE EXISTS,
TRANSMITTER SUPERVISORY TROUBLE
	THE CONSOLE WILL BEEP EVERY
IF A TRANSMITTER PROGRAMMED AS SUPERVISED FAILS	HOUR UNTIL CLEARED:
TO REPORT STATUS IN A 24 HOUR PERIOD, THE CONSOLE'S	2-BEEPS = CONSOLE LOW BATTERY
TROUBLE INDICATOR WILL LIGHT.	3-BEEPS = TRANSMITTER SUPERVISORY
CONSOLE BACKUP BATTERY TROUBLE	4-BEEPS = TRANSMITTER LOW BATTERY

THE CONSOLE WILL TEST ITS BACKUP BATTERY EVERY 8 HOURS.IF THE BATTERY TESTS LOW, THE POWER INDICATOR WILL BLINKSLOWLY WHILE THE CONSOLE CHARGES THE BATTERY.

ACTIVITY TIMER

1ENABLING THE ACTIVITY TIMERPRESS THE HOME BUTTON FOR 5 SECONDSTO TURN THE ACTIVITY TIMER ONNOTE: THE ACTIVITY TIMER CANBE ENABLED FOR 8, 12, OR 24 HOURS,OR DISABLED BY PROGRAMMINGNOTE: TO TURN THE ACTIVITYTIMER OFF, PRESS THE HOME BUTTONFOR FIVE SECONDS

- IN CASE OF EMERGENCY -
PRESS AND	- OR -
MOMENTIARLY	ACTIVATE
HOLD	EMERGENCY
EMERGENCY	TRANSMITTER
BUTTON
	PRESS TRANSMITTER
	BUTTON FOR AT LEAST
	2 SECONDS
CONSOLE	SIREN SOUNDS
IN ALARM	UNTIL CLEAR BUTTON
	IS PRESSED,
SENDING LIGHT	CENTRAL STATION
	REPORT IS COMPLETE,
FLASHES DURING
	OR SIREN TIME EXPIRES
COMMUNICATION
	PRESS CLEAR TO
	STOP SIREN
	(ADDS CANCEL TO
	ALARM REPORT IN
	PROGRESS)

THE CONSOLE WILL REPORT	NOTE: THE CONSOLE WILL ANNOUNCE
	THE SUPERVISORY CONDITIONS WITH
TROUBLE AND/OR 30-DAY STATUS
	THE OPTIONAL MODEL VB-4 VOICE
TO THE CENTRAL STATION IF
	BOARD INSTALLED. THE VOICE CAN
ENABLED IN THE COMMUNICATOR
	BE DISABLED THROUGH
PROGRAMMING
	PROGRAMMING

CLEARING TROUBLE INDICATIONS

PRESS THE CLEAR BUTTON TO STOP TROUBLEINDICATORS AND SOUNDERSNOTE: THE TROUBLE CONDITION WILL LIKELY OCCUR AGAIN UNTIL THE PROBLEM IS FIXED

2ACTIVITY TIMER RUNNING

THE HOME INDICATOR WILL LIGHT, SHOWING THAT THE ACTIVITY TIMER IS ENABLED

4RESETING ACTIVITY TIMER

THE SUBSCRIBER NEEDS TO PRESS THE HOME BUTTON OR TRIGGER AN ACTIVITY TRANSMITTER BEFORE THE TIMER EXPIRES TO PREVENT

AN INACTIVITY REPORTPRESSING THE HOME BUTTONRESTARTS THE TIMER

3TIME RUNNING OUT

THE HOME INDICATOR WILL BLINK & A SHORT BEEP SOUNDS EVERY 10 SECONDS WHEN LESS THAN 15 MINUTES OF TIME REMAIN

	AUDIO BOARD OPERATION
1	PROGRAM THE CONSOLE FOR	NOTE: TO USE THE AUDIO FEATURES
	THE DESIRED AUDIO MODE

THE MODEL VB-4 AUDIO MODULE

• LISTEN-ONLY	MUST BE INSTALLED IN THE CONSOLE
• 2-WAY MANUAL
• 2-WAY FULL DUPLEX

2AFTER THE CENTRAL STATION OPERATOR ACKNOWLEDGES THE COMMUNICATOR'S REPORT, THE CONSOLE WILL STOP ITS SIREN AND SWITCH TO THE AUDIO MODE FOR 90 SECONDS

3CENTRAL STATION OPERATOR:USE THESE KEYS ON A TELEPHONE SETCONNECTED TO THE COMMUNICATOR LINETO CONTROL THE AUDIO MODULE

ALL
AUDIO	PRESS "9" TO DISCONNECT THE CALL
MODES

PRESS "3" TO LISTEN2-WAY MANUALAUDIO MODEPRESS "1" TO TALKTHE "1" AND "3" KEYS ARE NOT USED IN LISTEN-ONLY AUDIO MODETHE "1" AND "3" KEYS CAN BE USED IN FULL DUPLEX MODE,ALTHOUGH THE MODULE WILL SWITCH TO 2-WAY MANUALMODE. PRESS "8" TO RETURN TO DUPLEX MODE.PRESSING ANY KEY OTHER THAN "9" WILL EXTEND THE AUDIO TIME 90 MORE SECONDS

SPECIFICATIONS

CODING FORMATS

DX CODE 24-BIT A1D PPM	1,048,567 CODES
DXS CODE 24-BIT A1D PPM	1,048,567 CODES

POWER REQUIREMENTS

PRIMARY SUPPLY	16 VAC 1.25 AMP PLUG-IN TRANSFORMER
BACKUP SUPPLY	12 VOLT 1.2 AMP/HOUR BATTERY
NORMAL OPERATING CURRENT	80 mA
ALARM OPERATING CURRENT	120 mA
BACKUP OPERATION DURATION	12 HOURS MINUMUM
BATTERY LIFE EXPECTED	3 YEARS

RF CHARACTERISTICS

RECEIVER TYPE	DUAL-DIVERSITY SUPERHETERODYNE
RF SENSITIVITY	-100 dBm TYPICAL
RADIO FREQUENCY	315 Mhz
MAXIMUM RANGE	400 FEET LINE-OF-SIGHT, OPEN RANGE
	UL LISTED FOR 150’

COMMUNICATOR

COMMUNICATOR FORMATS	4 BY 2 (GENERAL OR POINT-TO-POINT), ADEMCO
	CONTACT ID
	UL TESTED WITH SURGARD SGMLRG-DG CENTRAL
	STATION RECEIVER
DIALING	TONE OR PULSE
DIALING DELAY	0 OR 15 SECONDS
REMOTE ACCESS PASSWORD	6 DIGITS
ACCOUNT NUMBER LENGTH	4 DIGITS
PRIMARY TELEPHONE NUMBER	20 DIGITS
SECONDARY TELEPHONE NUMBER	20 DIGITS
SUPERVISORY TELEPHONE NUMBER	20 DIGITS
CONSOLE STATUS REPORT	OPTIONAL 1, 7 OR 30 DAY REPORT

CONSOLE

OPERATING TEMPERATURE	32°-100° F (0-50° C)
EMERGENCY ALARM DURATION	1-30 MINUTES
ACTIVITY TIMER PERIOD	8, 12, OR 24 HOURS
AUDIO	LISTEN-ONLY, 2-WAY MANUAL, 2-WAY DUPLEX
RELAY OUTPUT	N.O./N.C. (FORM C) @ 24 VOLT AC/DC 1 AMP
	MAXIMUM, NEC CLASS II CIRCUITRY

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.

•For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range.

•A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings.

•Changes or modifications to the device may void FCC compliance.

•Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

•A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users.