Gladiator Garageworks Freezer manual Cabinet

TOOLS NEEDED: %6 in. hex-head socket wrench, #2 Phillips screwdriver, flat-blade screwdriver, %6 in. open-end wrench, flat 2 in. putty knife.

IMPORTANT:

•Before you begin, turn the lower compartment control OFF, unplug freezer or disconnect power.

•Remove food and any adjustable door or utility bins from doors.

If you are only removing and replacing the doors, the instructions are the same regardless of door style. See the "Door and Hinge Removal" and "Door and Hinge Replacement" later in this section.

•All graphics referenced in the following instructions are included later in this section after "Final Steps."

Door and Hinge Removal

5/16in. Hex-Head Hinge Screw

1.Unplug freezer or disconnect power.

2.Open lower compartment door and remove base grille from the bottom front of the freezer (see Base Grille graphic).

3.Close the lower compartment door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to held the doors in place while you are working.

4.Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the upper compartment door free from the cabinet.

5.Remove the parts for the center hinge as shown in the Center Hinge graphic. Lift the lower compartment door free from the cabinet.

6.Remove the parts for the bottom hinge as shown in the Bottom Hinge graphic.

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, continue with the "Door Reversal (optional)" instructions. If you are not reversing the doors, see the "Door and Hinge Replacement" section.

::::: _×_ 3¸¸¸¸¸¸¸¸¸¸¸¸¸:¸¸¸¸¸:+¸+¸+:+:+¸¸¸¸¸¸:::+:+:+:::+::+: _ _ _ _ ._ ::::::

Door Reversal (optional)

(See complete graphics later in this section.)

Cabinet

1.Remove %6 in. hex-head hinge screws from handle side and move them to opposite side (see Graphic 1-1).

2.Remove cabinet hinge hole plugs from the cabinet top and move them to opposite side hinge holes as shown (see Graphic 1-2).

Doors

1.Remove door hinge hole plug from top of upper compartment door. Move to opposite side as shown (see Graphic 2).

2.Remove door stop from both the upper and lower compartment doors and move to the other side (see Graphic 3).

Door and Hinge Replacement

NOTE: Graphic may be reversed if door swing is reversed.

1.Replace the parts for the bottom hinge as shown. Tighten screws. Replace the lower compartment door.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

2.Assemble the parts for the center hinge as shown and tighten all screws (see Center Hinge graphic). Replace the upper compartment door.

3.Assemble the parts for the top hinge as shown (see Top Hinge graphic). Do not tighten screws completely.

4.Line up the doors so that the bottom of the upper compartment door aligns evenly with the top of the lower compartment door. Tighten all screws.

Final Steps

1.Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover (see Top Hinge graphic).

NOTE= On the left-hand side of the base grille there is a removable tab which is a bottom hinge hole plug. Break off the tab from the base grille and insert the bottom hinge hole plug into the bottom hinge holes (see Base Grille graphic).

2.Replace the base grille (see Base Grille graphic).

3.Plug in freezer or reconnect power.

4.Reset the controls, See "Using the Controls" section.

5.Return all removable door parts to doors and food to product.

Round-Head	Door Handle	Door Hinge
Handle Screw	Screw Hole Plug	Hole Plug