2. Press a Small Plastic Cap (31) into the Center | 2 |
| 20 |
|
|
|
Base (7). Attach the Eyebolt (17) to the Center |
|
|
|
| ||
|
|
|
|
|
| |
Base with an M10 Nylon Locknut (23) and two |
|
| 21 | 21 | 5 |
|
M10 Washers (21) as shown. |
|
|
| |||
|
|
|
|
|
| |
Attach the Center Base (7) to the Left and Right |
|
|
|
|
| 6 |
Bases (5, 6) with the four M10 x 65mm Bolts |
|
|
|
|
| |
|
|
|
| 17 |
| |
(20), four M10 Washers (21), and four M10 |
|
|
|
| 21 | |
|
|
|
| 21 | ||
Nylon Locknuts (23). Do not tighten the Nylon |
|
|
|
| ||
|
|
|
|
| ||
Locknuts yet. |
|
|
|
| 7 | 20 |
|
|
| 23 |
|
| |
|
|
|
|
|
| |
|
| 31 | 21 |
|
| 21 |
|
|
|
|
| ||
|
|
| 23 |
|
| |
|
|
| 23 |
|
| |
|
|
|
|
|
| |
3. Hold the Left and Right Braces (3, 4) against the | 3 |
|
|
|
|
|
Lower Frame (2) and the Left and Right Bases |
|
|
|
|
| |
|
| 23 |
|
|
| |
(5, 6). Attach the Braces to the Lower Frame with |
|
|
|
|
| |
|
|
|
|
|
| |
two M10 x 70mm Bolts (18) and two M10 Nylon |
|
|
|
|
|
|
Locknuts (23). Do not tighten the Nylon |
|
|
|
|
|
|
Locknuts yet. |
|
|
|
|
|
|
Tip the Lower Frame (2) and attach the Braces |
|
| 3 |
| 2 |
|
|
|
|
| 18 | ||
(3, 4) to the Bases (5, 6) with the two M10 x |
|
|
|
|
| |
|
|
|
|
|
| |
63mm Carriage Bolts (27) and two M10 Nylon |
|
|
|
|
|
|
Locknuts (23). |
|
| 23 |
|
|
|
|
|
|
|
| 4 | |
|
|
|
|
|
| |
Tighten all of the M10 Nylon Locknuts (23) |
| 5 |
|
|
|
|
used in steps 1, 2, and 3. |
|
|
|
|
| |
|
|
|
|
|
| 23 |
|
|
| 27 |
|
|
|
|
|
|
|
| 27 | 6 |
|
|
|
|
|
| |
4. See the inset drawing. Press the Large Plastic | 4 |
|
|
|
|
|
Cap (15) into the top of the Upper Frame (1). |
|
|
|
|
| |
|
| 1 |
|
| 15 | |
|
|
|
|
| ||
Hold one of the Large Plates (11) inside of the |
|
| 16 |
|
|
|
Lower Frame (2) as shown. Insert two M10 x |
|
|
|
| 21 |
|
15mm Screws (16) with M10 Washers (21) into |
|
|
|
|
| |
|
| 21 |
|
| 1 | |
the right side of the Lower Frame and finger |
|
|
|
| ||
|
|
|
| 16 |
| |
tighten them into the Large Plate. Attach the |
|
| 11 |
|
| |
other Large Plate (11) inside of the Lower Frame |
|
|
|
|
| |
in the same way. |
|
|
| 11 |
| |
|
|
| 16 |
| ||
Slide the Upper Frame (1) onto the two Large |
|
|
| 21 |
| |
|
|
|
|
| ||
Plates (11). Insert four M10 x 15mm Screws (16) |
|
| 21 |
|
|
|
with M10 Washers (21) into the Upper Frame |
|
|
|
|
| |
|
| 2 |
| 16 |
| |
and finger tighten them into the Large Plates. |
|
|
|
| ||
|
|
|
|
|
| |
Tighten all eight M10 x 15mm Screws (16). |
|
|
|
|
|
|
| 6 |
|
|
|
|
|
