Goodman Mfg ANSI Z21.47CSA-2.3 installation instructions 0140L00955 REV a

CPG1803503B* & CPG2404003B* THREE PHASE 208-230/60 HZ BELT DRIVE WIRING DIAGRAM

		SUPPLY VOLTAGE
L1		208-240/3/60			L2 L3
		T2	CC1
CC1	T1	T2
	T1	COMP1		T3	CC1
		T3
					C
				RCCF1
					F
					CM1

COMPONENT LEGEND

ALS	AUXILIARY LIMIT SWITCH
BC	BLOWER CONTACTOR
COMP	COMPRESSOR
CM	CONDENSER MOTOR
CC	COMPRESSOR CONTACTOR
CCH	CRANK CASE HEATER
CCHR	CRANK CASE HEATER RELAY
EM	EVAPORATOR MOTOR
F	FUSE
FC	FAN CAPACITOR

OR INSTALLING THIS PRESENT. FAILURE TO INJURY OR DEATH.

		C
	RCCF3
		F
			CM3
CC2		T2	CC2
	T1		T2
	T1	COMP2
		T3	BC
		T2
BC	T1
	EM	T3	BC

	C
RCCF2	F
	CM2
T3 CC2

1 3 VM

FS	FLAME SENSOR
GND	EQUIPMENT GROUND
GV	GAS VALVE
HPS	HIGH PRESSURE SWITCH
IBR	INDOOR BLOWER RELAY
IIC	INTEGRATED IGNITION CONTROL
IGN	IGNITOR
LPS	LOW PRESSURE SWITCH
LS	LIMIT SWITCH
PB	POWER DISTRUBTION BLOCK
PLF	FEMALE PLUG/CONNECTOR
PS	PRESSURE SWITCH
RS	ROLLOUT SWITCH
TB1	TERMINAL BLOCK (24V SIGNAL)

HIGH VOLTAGE! DISCONNECT ALL POWER BEFORE SERVICING UNIT. MULTIPLE POWER SOURCES MAY BE DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL

	CCH1
			2	1
			2	1	208-240v
	CCH2
				3	2	1
				TB1
			S2	S1		TR
L1	NOTE 3				24V			NOTE 3
						IGN		L2
	1							IIC
				FS		FS
	F		H C					BC
4				D1		6	4
					LS	VMR
5
			3		ALS	RS		GV
	IIC
			6					CC2
					PS
						LPS2		HPS2
			8
9	2		ECON
		7	10	12	HPS1	LPS1
				11				CC1
					6	4	6	4

TB2	TERMINAL BLOCK (L1)
TR	TRANSFORMER
VM	VENT MOTOR
VMR	VENT MOTOR RELAY

NOTES

1.REPLACEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS ORIGINAL.

(USE COPPER CONDUCTOR ONLY).

2. ACCESSORY ECONOMIZER PLUG ADJACENT TO BLOWER HOUSING IN RETURN AIR COMPARTMENT. REMOVE MALE PLUG AND ATTACH FEMALE PLUG TO THE ECONOMIZER ACCESSORY.

3. L1 AND L2 ON IIC CONTROL IS 24V INPUT.

4.USE COPPER CONDUCTORS ONLY.

USE NEC CLASS 2 WIRE.

5.FOR TWO STAGE OPERATION REMOVE W1 TO W2 WIRE JUMPER.

6.FOR 208V OPERATION MOVE BLACK WIRE FROM TERMINAL 3 TO TERMINAL 2 ON THE

TRANSFORMER.

			CCHR1			CCHR2
			NOTE 5			PLF	9	6	3
			Y1	Y
R	G	W1 W2			C	2	8	5	2
				Y2			7	4	1
	TO THERMOSTAT				TB1

INSTALLER/SERVICEMAN

THE STATUS LIGHT ON THE FURNACE CONTROL MAY BE USED AS A GUIDE TO TROUBLESHOOTING THIS APPLIANCE. STATUS LIGHT CODES ARE AS FOLLOWS:

STATUS LIGHT	EQUIPMENT STATUS	CHECK
ON	NORMAL OPERATION	------
	NO POWER OR	CHECK INPUT POWER
OFF		CHECK FUSE ON CONTROL
	INTERNAL CONTROL
		REPLACE CONTROL
	IGNITION FAILURE	GAS FLOW
	OPEN ROLLOUT	GAS PRESSURE
		GAS VALVE
1 BLINK	SWITCH	FLAME SENSOR
	OPEN AUX. LIMIT	FLAME ROLLOUT
		BAD SWITCH
	SWITCH	AUX. LIMIT OPEN
2 BLINKS	PRESSURE SWITCH	CHECK
	OPEN	PRESSURE SWITCH
3 BLINKS	PRESSURE SWITCH CLOSED	CHECK
	WITHOUT INDUCER ON	PRESSURE SWITCH
4 BLINKS	OPEN LIMIT SWITCH	MAIN LIMIT OPEN
		BAD SWITCH
5 BLINKS	FALSE FLAME SENSED	STICKING GAS VALVE
6 BLINKS	COMPRESSOR	3 MIN. COMP.
	OUTPUT DELAY	ANTI-CYCLE TIMER

FACTORY WIRING

			LINE VOLTAGE
			LOW VOLTAGE
			OPTIONAL
			HIGH VOLTAGE
	FIELD WIRING
			HIGH VOLTAGE
			LOW VOLTAGE
	WIRE CODE
BK		BLACK
BL			BLUE
BR		BROWN
GR			GREEN
OR			ORANGE
PK			PINK
PU			PURPLE
RD			RED
WH			WHITE
YL			YELLOW
YL/PK			YELLOW WITH
			PINK STRIPE
BL/PK			BLUE WITH
			PINK STRIPE

THERMOSTAT

FIELD WIRING

2 STAGE COOLING
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y1
Y/Y2	PK	Y2
C	BL	C
O	OR	O
TB1		STAT
NO ECONOMIZER
W	WH	W
G	GR	G
R	RD	R
Y1
Y/Y2	YL	Y2
C	BL	C
O	OR	O

TB1STAT

WITH ECONOMIZER OPTION

W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y

Y/Y2
C	BL	C
O	OR	O

TB1STAT

SEE UNIT RATING PLATE FOR TYPE AND SIZE

OF OVER CURRENT PROTECTION

0140L00955 REV A

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

29