PARTS LIST
CHECK that you have all the parts listed below
BEFORE assembling your stroller.
If any parts are missing,
call Customer Service at
or visit our Internet website, www.gracobaby.com.
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
Frame
Large wheel (4)
Front axle (short) (on certain models) (on certain models)
Rear axle (long)
Parent’s tray
(on certain models)
Brake wire
Retainer | Cap | Hub |
|
(4, 1 extra) | (4, 1 extra) | adapter | (2) |
|
|
|
|
OR
Arm bar
(on certain models)
Child’s tray
(on certain models)
Rear axle Front axle mount (2)
mount (2) (on certain models)
The following parts are only included on models with front swivel wheels:
Retainer
(2, 1 extra)
Front swivel Large wheel (2)
assembly (2) | Cap | |
(2, 1 extra) | ||
|
To Unpack Stroller
Step 1.
Flatten stroller carton to protect floor.
Step 2. | Flattened carton |
| |
|
| ||
Open stroller on carton until | Locking | ||
latch | |||
locking latches on both sides | |||
| |||
are locked as shown. |
|
| |
Step 3. |
|
| |
Push down on the footrest until |
| ||
it snaps on the bar under it. |
| ||
To Assemble Rear Axle
Step 1. | Brake |
wire slot | |
Push rear axle mounts onto |
|
brake wire as shown. It is very |
|
important to insert the brake |
|
wire into the axle mounts |
|
correctly. If it is not, the brakes |
|
will not work properly. |
|
Push rear axle |
|
mounts onto brake wire |
|
Red brake
on top
Brake wire
angles toward rear of stroller
Step 2.
Turn stroller over as pictured above.
Step 3.
Position rear axle mount assembly and brake wire as shown.
Push assembly onto rear legs until plastic tabs snap into the slots on the legs.
Step 4.
Pull firmly on each axle mount to be sure it is securely attached.
HINT: If the axle mounts do not snap on the legs, they may be facing the wrong way. Remove the axle mounts with brake wire and face them the other way.
Step 5.
Insert rear axle (longer axle) |
|
through holes in the rear axle |
|
mounts. It may be necessary to |
|
twist the axle mount slightly to | Axle |
get the axle through the holes. |
|
To Assemble Rear Wheels
Place parts in order on rear axle as shown. If the hub adapter will not go against the rear axle mount, push the brake wire down and check to make sure the hub adapter is aligned in the wheel correctly.
| Hub adapter |
| toward inside |
| Wheel |
Rear | Cap (white) |
Attach AFTER | |
axle | retainer is on axle |
| Retainer (red) |
| Wide end toward wheel |
Be sure cap is snapped securely over red retainer.
To Assemble Front Axle*
Pointed
Step 1.side to back
Put both front axle mounts on
the frame. (The pointed side of
the axle mount faces the rear of Footrest the stroller.)
Step 2.
Put the axle through the hole in the axle mount and frame. It may be necessary to twist the axle mount slightly to get the axle into the hole.
To Assemble Front Wheels*
Place parts in order on front axle as shown. Push red retainer onto axle BEFORE attaching white cap. Repeat on other side.
Wheel
Axle | Cap (white) | |
Attach AFTER | ||
| ||
| retainer is on axle | |
| Retainer (red) | |
| Wide end toward wheel |
Be sure cap is snapped securely over red retainer.
To Assemble Front Swivel Wheels*
To prevent serious injury or | End cap | |
death from choking, remove | ||
| ||
and IMMEDIATELY discard |
| |
the plastic end caps on the |
| |
front leg pins. |
|
Step 1.
Line up pin with a wheel assembly as shown.
Step 2.
Push wheel assembly onto pin until it snaps in place.
Step 3.
Repeat for other wheel assembly.
Pull firmly on each wheel assembly to be sure the wheel assemblies are securely attached.
*On certain models
5 | 6 | 7 | 8 |
