![](/images/new-backgrounds/1314836/31483639x1.webp)
SECTION 6: SERVICE
Review the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570)
Troubleshooting
Motor & Electrical
Symptom |
| Possible Cause | Possible Solution | ||||
Motor will not start. | 1. | Low voltage. | 1. | Check power line for proper voltage. | |||
|
|
|
| 2. | Open circuit in motor or loose connections. | 2. | Inspect all lead connections on motor for loose or open |
|
|
|
|
|
|
| connections. |
|
|
|
|
| |||
Motor will not start; | 1. | Short circuit in line cord or plug. | 1. | Inspect cord or plug for damaged insulation and shorted | |||
fuses | or | circuit |
|
|
| wires. | |
breakers blow. |
| 2. | Short circuit in motor or loose connections. | 2. | Inspect all connections on motor for loose or shorted termi- | ||
|
|
|
| ||||
|
|
|
|
|
|
| nals or worn insulation. |
|
|
|
| 3. | Incorrect fuses or circuit breakers in power line. | 3. | Install correct fuses or circuit breakers. |
|
|
|
|
| |||
Motor overheats. | 1. | Motor overloaded. | 1. | Reduce load on motor. | |||
|
|
|
|
| |||
Motor stalls (result- | 1. | Short circuit in motor or loose connections. | 1. | Inspect connections on motor for loose or shorted terminals | |||
ing in blown fuses |
|
|
| or worn insulation. | |||
or tripped circuit). | 2. | Low voltage. | 2 | Correct the low voltage conditions. | |||
|
|
|
| ||||
|
|
|
| 3. | Incorrect fuses or circuit breakers in power line. | 3. | Install correct fuses or circuit breakers. |
|
|
|
| 4. | Motor overloaded. | 4. | Reduce load on motor. |
|
|
|
|
|
| ||
Machine | slows | 1. | Operator is using too much pressure. | 1. | Use less pressure when grinding. | ||
when operating. |
|
|
|
|
| ||
|
|
|
|
|
|
| |
Wavy |
| condi- | 1. | Machine vibrating. | 1. | Make sure machine is securely mounted on a solid sur- | |
tion on | surface | of |
|
|
| face. | |
workpiece. |
|
| 2. | Workpiece not being held firmly. | 2. | Use a holding device to firmly retain the workpiece. | |
|
|
|
| ||||
|
|
|
| 3. | Wheel face uneven. | 3. | Dress the grinding wheel. |
|
|
|
| 4. | Wheel is too hard. | 4. | Use softer wheel, or reduce the feed rate. |
|
|
|
|
| |||
Lines on surface of | 1. | Impurity on wheel surface. | 1. | Dress the grinding wheel. | |||
workpiece. |
|
| 2. | Workpiece not being held tightly. | 2. | Use a holding device to firmly retain the workpiece. | |
|
|
|
|
|
| ||
Burning | spots | 1. | Improper type of grinding wheel. | 1. | Try a wheel which is softer style or a coarser grit. | ||
or cracks | in | the | 2. | Improper feed rate. | 2. | Slow down the rate of movement of the workpiece into | |
workpiece. |
|
|
|
|
| wheel. | |
|
|
|
|
|
|
| |
|
|
|
| 3. | Coolant required. | 3. | Add optional coolant system or introduce coolant by hand. |
|
|
|
|
| |||
Wheel dulls quickly, | 1. | Depth of cut too great. | 1. | Slow down the rate of movement of the workpiece into | |||
grit falls off. |
|
|
|
|
| wheel. | |
|
|
|
| 2. | Wheel is too soft. | 2. | Wheel too soft for the material being ground, select harder |
|
|
|
|
|
|
| bond. |
|
|
|
| 3. | Wheel diameter too small. | 3. | Replace the wheel. |
|
|
|
| 4. | Bad wheel dress. | 4. | Dress the wheel. |
|
|
|
| 5. | Defective wheel bonding. | 5. | Consult manufacturer of grinding wheel. |
|
|
|
|
|
|
|
|
Model |