Cutting Rabbets with a Standard Blade
6g^ee^c\WaVYZ^hine^XVaani]ZWZhiWaVYZidjhZ [dg Xjii^c\ gVWWZih l]Zc jh^c\ V hiVcYVgY WaVYZ WZXVjhZ^igZbdkZhhVlYjhikZgnZ[[^X^Zcian# HZZ Page 29[dgWaVYZYZiV^ah# 6ahd!VhVXg^[^X^Va[ZcXZ ^hcdigZfj^gZYl]ZcXjii^c\gVWWZihl^i]VhiVc" YVgYWaVYZ#
To cut rabbets with the standard blade:
1.9>H8DCC:8IH6L;GDBEDL:G
2. :chjgZ i]Vi i]Z g^k^c\ `c^[Z VcY hiVcYVgY iVWaZ^chZgiVgZ^chiVaaZY#
3. BVg`i]Zl^Yi]d[i]ZgVWWZiXjidci]ZZY\Z d[i]Zldg`e^ZXZ!hdndjXVcXaZVgan^YZci^[n i]Z^ciZcYZYXjil]^aZ^i^haVn^c\[aVidci]Z hVliVWaZ#
4. GV^hZi]ZWaVYZjeidi]ZYZh^gZYYZei]d[Xji YZei]d[gVWWZiX]VccZaYZh^gZY #
5. HiVcY i]Z ldg`e^ZXZ dc ZY\Z! Vh h]dlc ^c Figure 57, i]ZcVY_jhii]Z[ZcXZhdi]ZWaVYZ ^hVa^\cZYl^i]i]Z^ch^YZd[ndjggVWWZiX]Vc" cZa#
Blade | dg`e^ZXZL |
|
|
| |
|
| ;ZcXZ |
Figure 57. GVWWZiXjii^c\l^i]VhiVcYVgYWaVYZ#
>[i]Zldg`e^ZXZ^hkZgniVaa! dg^hjchiVWaZ l]ZceaVXZYV\V^chii]Z[ZcXZ!aVn^i[aVidc i]ZiVWaZVcYjhZVYVYdWaVYZideZg[dgb i]ZgVWWZiXji#
45
15 | 30 |
DO NOT place a tall board on edge to per- form a rabbet cut with a standard blade. Workpieces that are too tall to properly support with the fence can easily shift dur- ing operation and cause kickback. Instead, place the stock flat on the saw and perform the rabbet cut with a dado blade, as instruct- ed on Page 41.
6. GZXdccZXii]ZhVlidi]ZedlZghdjgXZ!i]Zc eZg[dgbi]ZXji#
7. AVni]Zldg`e^ZXZ[aVidci]ZiVWaZ!Vhh]dlc ^cFigure 58!VY_jhii]ZhVlWaVYZ]Z^\]iid ^ciZghZXi l^i] i]Z [^ghi Xji! i]Zc eZg[dgb i]Z hZXdcYXjiidXdbeaZiZi]ZgVWWZi#
Blade |
;ZcXZ |
Ldg`e^ZXZ |
Figure 58. HZXdcYXjiidXgZViZVgVWWZi# |
")'" | BdYZa<%,&*E B[\#)$&& |
