Figure 14. Column adjustment flange

underneath table.

8.Loosen the two nuts that secure the table adjustment flange; this will allow the opposite side of the table to be moved up or down.

9.Turn the fine adjustment knob to raise the side of the table with the Rotacator® to make the dial read .050" on the Rotacator dial. Double check the table-to-cutterhead measurement on the right end to make sure it did not move. Adjust as necessary. The Rotacator® will allow you to easily get each end within ±.001" of each other.

10.When each end is adjusted properly, tighten all of the nuts at the table mount and clamp. Double check the table-to-cutterhead mea- surement to make sure the table did not move.

To adjust the table with the wood block:

1.Make sure the planer is disconnected from the power source!

2.Place the wood block on the side of the table where the tightest gap exists between the table and the cutterhead.

3.Raise the table so the cutterhead barely touches the wood block. Slide the wood block to the other side of the table, under the other end of the cutterhead.

4.Locate the two columns underneath the table. These are covered in flexible rubber sleeves. Underneath the sleeves are adjust- ment flanges that allow you to disengage the table columns from the lifting gears.

To adjust the table, you need to disen- gage the opposite side that needs to be adjusted.

5.Pull the rubber sleeve down on the deter- mined column to expose the table adjust- ment flange shown in Figure 14. You may need to cut the plastic cable tie in order to remove the sleeve.

6.Loosen the two nuts that secure the table adjustment flange; this will allow the opposite side of the table to be moved up or down.

7.Turn the fine adjustment knob to raise the side of the table with the wood block, so the wood block barely touches the cutterhead.

8.Slide the wood block over to the other side to check for consistency. Adjust the table as necessary until each side is even with each other. Use a feeler gauge to check the toler- ances.

9.Tighten the two nuts that secure the table adjustment flange. Double check the table- to-cutterhead measurement to make sure the table did not move.

10.Pull the rubber sleeve back up to its original position. Be sure to secure it with a new plastic cable tie if you cut the old one. The rubber sleeves must cover the lifting column to keep fine sawdust from building up in the gear grease.

11.Set the table rollers as necessary.

-28-

Extreme Duty Planers

Page 35 Page 37
Page 36
Image 36
Grizzly G9740 instruction manual
Page 35 Page 37

G9740 specifications

The Grizzly G9740 is a versatile and powerful benchtop metal band saw designed for enthusiasts and professionals alike. Known for its robust construction and high performance, this machine stands out as an essential tool for any workshop that requires precise cutting of metal materials.

One of the main features of the G9740 is its powerful 1 HP motor, which delivers smooth and consistent cutting performance. This motor provides the necessary torque to handle a variety of metal cutting tasks, from simple cross-cuts to complex curves. Additionally, the saw operates at two different speeds, allowing users to adjust the cutting rate according to the material being worked on, which enhances its versatility.

The G9740 is engineered with a durable cast iron frame that not only reduces vibration but also contributes to the overall stability of the saw during operation. This stability is crucial for achieving accurate cuts, especially when working with thicker materials. The band saw is equipped with a precision ground cast iron table that provides ample support for the workpiece, ensuring that it can handle large and heavy materials with ease.

Another notable characteristic of the Grizzly G9740 is its large cutting capacity. The saw can accommodate stock up to 7 inches in height and 10 inches in width, making it ideal for a wide range of projects, from custom metal fabrications to intricate hobby work. The adjustable blade guide system ensures that the blade remains properly aligned, which is essential for maintaining cutting accuracy over extended periods.

Safety is a top priority with the Grizzly G9740. The machine comes with several safety features, including a blade guard that protects users from accidental contact with the cutting blade. Moreover, the saw is designed with a reliable tensioning mechanism that keeps the blade tight and secure during operation, minimizing the risk of blade breakage or misalignment.

In summary, the Grizzly G9740 is a highly capable benchtop metal band saw that offers a combination of power, precision, and safety. Its robust design, flexible speed settings, and generous cutting capacity make it an excellent choice for anyone looking to tackle metal cutting projects with confidence and accuracy. Whether for professional use or personal projects, the G9740 is a reliable tool that will deliver consistent and high-quality results.
Top Page Image Contents