To check the table with the block of wood:

1.Make sure the planer is disconnected from the power source!

2.Models G9740Z and G9967Z skip this step. For Models G9740 and G9967, open the left side service door. Locate the cutterhead lock shown in Figure 11. Pull up and twist so the end of the lock will drop. Rotate the pulley to line up the cutterhead lock with the THREADED HOLE in the pulley (this should position the cutterhead so the knives are out of the way for table adjustments).

3.Place the block of wood on the table, under- neath the cutterhead. Position the block on the left side (point “A” in Figure 13) of the cutterhead.

A

 

CUTTERHEAD

B

*

 

 

TABLE

 

 

 

 

Figure 13. Measure table-to-cutterhead at both

points “A” and “B.”

4.Raise the table up until the top of the block lightly contacts the bottom of the knife or indexable insert, depending on your model.

5.Without moving the table position, slide the block over to the other side (point “B” in Figure 13).

6.If the block will not fit under the cutterhead or if the gap between the block and the cutterhead exceeds .004" (use a feeler gauge to measure this), the table must be adjusted.

To adjust the table with the Rotacator®:

1.Make sure the planer is disconnected from the power source!

2.Set the Rotacator® dial to .000". Place the Rotacator® under the cutterhead on the right- hand side (facing front).

3.Turn the cutterhead so the plunger on the Rotacator® contacts the cutterhead body. Raise the table up enough for the cutterhead to get a reading on the dial.

4.Move the Rotacator® back and forth to find bottom dead center on the cutterhead. (You will reach bottom dead center when you have the highest reading on the Rotacator®.)

5.Adjust the table height to make the dial on the Rotacator® read .050", then set the dial to .000". Move the Rotacator® over to the far left end of the cutterhead and find bottom dead center.

6.Locate the two columns underneath the table. These are covered in flexible rubber sleeves. Underneath the sleeves are adjust- ment flanges that allow you to disengage the table columns from the lifting gears.

To adjust the table, you need to disen- gage the opposite side from that which needs to be adjusted.

7.Pull the rubber sleeve down on the deter- mined column to expose the table adjust- ment flange shown in Figure 14. You may need to cut the plastic cable tie in order to remove the sleeve.

Extreme Duty Planers

-27-

Page 35
Image 35
Grizzly G9740 instruction manual Cutterhead

G9740 specifications

The Grizzly G9740 is a versatile and powerful benchtop metal band saw designed for enthusiasts and professionals alike. Known for its robust construction and high performance, this machine stands out as an essential tool for any workshop that requires precise cutting of metal materials.

One of the main features of the G9740 is its powerful 1 HP motor, which delivers smooth and consistent cutting performance. This motor provides the necessary torque to handle a variety of metal cutting tasks, from simple cross-cuts to complex curves. Additionally, the saw operates at two different speeds, allowing users to adjust the cutting rate according to the material being worked on, which enhances its versatility.

The G9740 is engineered with a durable cast iron frame that not only reduces vibration but also contributes to the overall stability of the saw during operation. This stability is crucial for achieving accurate cuts, especially when working with thicker materials. The band saw is equipped with a precision ground cast iron table that provides ample support for the workpiece, ensuring that it can handle large and heavy materials with ease.

Another notable characteristic of the Grizzly G9740 is its large cutting capacity. The saw can accommodate stock up to 7 inches in height and 10 inches in width, making it ideal for a wide range of projects, from custom metal fabrications to intricate hobby work. The adjustable blade guide system ensures that the blade remains properly aligned, which is essential for maintaining cutting accuracy over extended periods.

Safety is a top priority with the Grizzly G9740. The machine comes with several safety features, including a blade guard that protects users from accidental contact with the cutting blade. Moreover, the saw is designed with a reliable tensioning mechanism that keeps the blade tight and secure during operation, minimizing the risk of blade breakage or misalignment.

In summary, the Grizzly G9740 is a highly capable benchtop metal band saw that offers a combination of power, precision, and safety. Its robust design, flexible speed settings, and generous cutting capacity make it an excellent choice for anyone looking to tackle metal cutting projects with confidence and accuracy. Whether for professional use or personal projects, the G9740 is a reliable tool that will deliver consistent and high-quality results.