GTO 352 Parts List - Opener and Mounting Hardware

Mighty Mule 352

Parts List - Opener and Mounting Hardware

Hairpin Clip (4)

3/8" x 1-1/2" Clevis Pin (4)

5/16" x 1-3/4" Bolt (2)

3/8" x 2" Bolt (2)

3/8" x 3" Bolt (4)

3/8" x 8" Bolt (8)

8" Nylon Cable Tie (14)

3/8" Washer (18)

3/8" Lock Washer (14)

5/16" Washer (2)

3/8" Nut (14)

5/16" Nut (2)

Hardware Bag Contents

Second Opener (1)

Master Opener (1)

Post Pivot Bracket (2)

3/8" Bushings (4)

32’ Communication

Cable (1)

Gate Bracket (2)

Post Bracket (4)

Closed Position

Stop Plate (1)

2" Mounting Screw (5)

Installation Video (1)

Customer Support Card (1)

Transformer (1)

Warning Signs (4)

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or

play in gate area.

3. This gate is for vehicles only. Pedestrians

must use a separate entrance.

Moving Gate Can Cause

Injury Or Death

WARNING

Receiver (1)

10’ Master

Battery

Harness (1)

GTO Transmitter (1)

32’ Second Opener

Battery Harness (1)

10’ Master

Battery Harness (1)

Contents

Main Installation Manual for the WARNING! E-Z GATE OPENER FOR YOUR RECORDS Remember to keep all receipts for proof of purchase. Conversion Chart ConvertingMetricUnitstoEnglishEquivalents When You Know Multiply By To Find Symbol ConvertingEnglishUnitstoMetricEquivalents Table of Contents KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PLEASE READ THIS FIRST! E-Z GATE OPENERS Disconnecting the Opener To Manually Open and Close the Gate, Follow the Procedure Below: IMPORTANT: 0caVW\U CAUTION: For The Consumer WARNING: To reduce the risk of injury or death: Entrapment Zones for a Pull-To-Open Application Moving Gate Area 10'10' Moving Gate Area Driveway 10'10' 10'10' NEVER INSTALL any control device within gray area Pull-To-Open Application Page ENTRAPMENT ALARM (UL 325; 30A.1.1A) Secondary Means of Protection Against Entrapment Install Warning Signs WARNING Entrapment Protection Required Safety Precautions for Gates ! ! ! ! E-Z GATE OPENER Can Cause Injury or Death Parts List - Opener and Mounting Hardware Hardware Bag Contents Tools Needed MIGHTY MULE 352 E-Z GATE OPENER Technical Specications Preparation of the Gate Step 1 Step 2 Installation Overview Pull-to-Open Gates (Gate Opens into the Property) Installation of Mounting Hardware Recommended Reinforcement Examples Determining the Mounting Position of the Post Bracket Assembly and the Gate Bracket Step 5 Bushing Hairpin Clip Post Bracket Assembly Step 6 IMPORTANT: TIP: Installing the Post Bracket Assembly and Gate Bracket Step 7 Step 8 Step 9 Step 10 Gate Bracket Mounting Examples Mounting the Master Opener Step 11 Mounting the Second Opener Step 12 Installation of the Closed Position Stops Step 3 NOTE: Step 2 Page Preparing to Connect the Wires Trench and Lay Conduit for Wiring IMPORTANT: ON/OFF Attaching Master Opener Battery and Communication Cables ON/OFF Attaching Second Opener Battery and Communication Cables At this point your gate openers should be connected like the picture below. Powering Options: Transformer or Solar IMPORTANT: Solar Panel and Gate Activity Chart NEVER USE TRANSFORMER AND SOLAR PANEL(S) AT THE SAME TIME it will damage the control board Connecting The Battery Connecting the Transformer PVC conduit (not included) to protect wire from lawn mowers and weed eaters. Step 1 IMPORTANT INFORMATION ABOUT LOW VOLTAGE WIRE DO NOT Page Master Control Board Settings Connecting Solar Panel(s) () DIP Switches Main DIP Switch Settings (MODES) Setting Auto-Close Time Stall Force Potentiometer Setting MASTER Installing the Receiver NOTE: Do not mount upside down. Setting the Closed Position Limit For PULL-TO-OPEN Installation ON/OFF Turn the power switches on the opener arms to the ON position 2. Set the transmitter DIP Switches Setting Your Personal Transmitter Code 1. Remove the Transmitter Cover 3. Teach the New Code to Control Board Memory Page Control Board Connections Connecting Accessories GTO Photo Beams GTO Loop Detector GTO Universal Receiver Push Button Control Routing Wires Through The Access Panel Second Opener Master Opener Final Step When everything has been connected to the opener... Gate in the Closed Position Pinch Area (gray) Gate in the Open Position Pinch Area (gray) 2" minimum 2" minimum Push to Open Installation Post Bracket Assembly IMPORTANT: Setting the Open Position Limit Page Audible/Buzzer/Alarm Feedback: Visual/LEDs Feedback: Visual and Audible Diagnostic Indicators The Gate CLOSES Then Opens Again on its Own: The Gate OPENS Then Closes Again on its Own: VOLTAGE RATINGS Repair Service GTO, Inc. E-Z GATE OPENERS Column Installation Information I Accessories are Available From Your Retail Store E-Z GATE OPENERS ACCESSORIES Solar Panel (FM123) 10 watt (FM121) 5 watt -requirestwo-5wattpanels Push Button Control (FM132) Pin Lock (FM133) Key Chain Two Button Transmitter (FM134) If you have a question about any special order item, just call 1-800-543-GATE! Accessories are Available From Your Retail Store (con't)