Section 3 – Post-installation Start-up Adjustments

Recreational Vehicle Generator

‹2.9.1 REMOTE PANEL MODELS

The remote panels mount a rocker type start/stop switch, a “Generator Run” advisory lamp and an hourmeter. The hourmeter should be used in con- junction with the maintenance operations found in Part I of this manual.

Model 004057 includes the remote panel and a 10 foot long, 4 wire harness.

Model 004184 includes the remote panel and a 30 foot long, 4 wire harness.

3.1POST INSTALLATION TESTS

The air-cooled generator set was factory tested and adjusted. It should not be required to adjust the unit any further except under special circumstances.

Do not make any unnecessary adjustments. Factory settings are correct for most applications. When making adjustments, however, be careful to avoid overspeeding the engine.

3.2BEFORE INITIAL START-UP

Before starting, complete the following:

1.Check the engine crankcase oil level and, if nec- essary, fill to the dipstick “FULL” mark (cross- hatched area) with the recommended oil. Do not fill above the FULL mark.

2.Check the fuel supply. Gas fuel lines must have been properly purged and leak tested in accor- dance with applicable fuel codes. All fuel shutoff valves in the fuel supply lines must be open.

DANGER

If a liquid propane (LP) gas fuel system has been installed, it must be properly tested for leaks before operating the system in compliance with ANSI A119.2/NFPA 501C. No leakage is permitted. Be sure no gasoline fuel vapors enter the vehicle interior.

3.3INITIAL START

When absolutely certain that the unit has been prop- erly installed and prepared for use, start the engine as follows:

1.Turn off all electrical loads. Do this by setting the generator’s main circuit breakers to their “OFF” (or open) position.

2.Refer to Part I, section “Starting the Generator”, for cranking and starting instructions. The engine may require more cranking for initial starting since the fuel lines have to be primed (use of the primer switch will shorten this time).

3.Let the engine warm up for about five minutes to allow internal temperatures to stabilize.

4.Carefully inspect the engine/generator for fuel, oil and exhaust system leaks. Before proceeding to the next step, correct any leakage immediately.

5.When all tests and adjustments at no-load are completed, apply electrical loads and check for proper operation under load. See the "Testing Under Load" section. Run the unit at least 30 minutes with loads applied.

6.Turn off all electrical loads by setting the gener- ator’s main circuit breakers to their “OFF” (or OPEN) position.

7.Let the unit run at no-load for a few minutes to stabilize internal engine/-generator temperatures. Then, shut down the engine.

NOTE:

The generator set was thoroughly tested and adjusted at the factory before shipping. No addi- tional adjustment should be necessary. Only quali- fied service technicians who have been trained should perform adjustments outlined in this manual.

3.4TESTING UNDER LOAD

Apply electrical loads equal to about 75 to 100 per- cent of the unit's rated wattage/amperage capacity.

Let the unit run at least 30 minutes with load applied. During this part of the test, check that the unit is not running excessively hot and that adequate cooling airflow is available. Do not allow the unit to overheat during prolonged operation.

NOTE:

The generator engine is equipped with a high tem- perature switch. The switch has normally closed (N.C.) contacts. When the engine temperature is too high, switch contacts close, and the engine shuts down automatically.

THE MANUFACTURER RECOMMENDS TESTING THE GENERATOR FOR ADEQUATE COOLING.

35

Page 37
Image 37
Guardian Technologies 04164-3, 02010-2 Post Installation Tests, Before Initial START-UP, Initial Start, Testing Under Load

04164-3, 02010-2 specifications

Guardian Technologies is proud to present the innovative 02010-2,04164-3 model, a standout product in its line of advanced air quality solutions specifically designed for modern homes. This cutting-edge air purifier is engineered to enhance indoor air quality, making it essential for those who prioritize a clean living environment.

One of the main features of the Guardian Technologies 02010-2,04164-3 is its powerful three-stage filtration system. This includes a pre-filter, a true HEPA filter, and an activated carbon filter, which work synergistically to capture a wide range of airborne pollutants. The pre-filter traps larger particles such as dust and pet hair, while the HEPA filter is capable of capturing 99.97% of allergens as small as 0.3 microns, including pollen, smoke, and mold spores. The activated carbon filter effectively reduces odors from pets, cooking, and smoke, providing a fresher living space.

In addition to its robust filtration capabilities, the 02010-2,04164-3 is equipped with Guardian Technologies' proprietary UVC light technology. This feature helps to further reduce airborne bacteria and viruses, giving users added peace of mind, especially in today’s health-conscious world. The UVC light works in conjunction with the filtration system to ensure a comprehensive level of air purification.

Another notable characteristic of this model is its compact and stylish design, making it suitable for any room in your home, whether it be the living room, bedroom, or office. Its lightweight construction allows for easy portability, letting users move it as needed for maximum efficiency.

The Guardian Technologies 02010-2,04164-3 also boasts user-friendly features, including a programmable timer and multiple fan speeds, allowing users to customize the airflow according to their preferences. Additionally, the quiet operation ensures that it does not disrupt daily activities or sleep, making it perfect for nighttime use.

In summary, the Guardian Technologies 02010-2,04164-3 air purifier combines advanced filtration technology, UVC light purification, and user-friendly features in a sleek design. It is an excellent choice for anyone looking to improve indoor air quality and create a healthier living environment.