Haier DW12-BFE ME manual Turning on the Appliance

Turning on the Appliance

Starting a wash cycle￿

After having completed all of the installation steps in the pre- ceding paragraphs, turn on the water all the way and press the ON-OFF button (A) located on the control pannel. The "B" indi- cator light will come on. At this point, the appliance is on but you must wait a few seconds before programming the setting for the cycle.

Setting and Starting a wash Cycle

Select the desired cycle by pressing the selector button (G). Each time the button is pressed, one of the"H" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance).

Press the Start/Pause button(I), and after a few seconds a short acoustic sound will indicate that the wash cycle has begun and can no longer be changed. If necessary ,read the paragraph entitled " Cancelling or modifying a cycle while underway..."

Cancelling or modifying a cycle while underway ￿

Premise : A cycle that is underway can only be modified if it has only been running for a short time.Otherwise, the detergent may have already been used,and the appliance mayhave already drained the wash water. If this is the case,the detergent dis- penser must be refilled (see the paragraph entitled,"Loading the Detergent").

To modify a cycle that is already underway, press the ON-OFF button (A) ,then all of the settings will be cancelled.

If you forget to load some of the dishes￿

The wash cycle can be interrupted by pressing the Start/Pause button.You can then load additional dishes and turn the appli- ance back on.The cycle will start where it left off.

Wash cycle Program Light

The wash cycle is running and the cycle indicator light (H) for the cycle will begin to blink.

At the end of the wash cycle￿

Six acoustic signal will indicate that the wash cycle has finished and the cycle indicator light (H) for the cycle will begin to die out. Turn off the appliance using the ON-OFF button.Turn off the water supply to the appliance and open the door. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better.

Setting the Wash Cycle with a Delayed Start Time

Premise: After selecting the wash cycle as indicated in the para- graph entitled ,"Setting and Starting a Wash Cycle..."the delay time can be set.

By pressing the "E" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed,the display (F) will show the number of hours for the delay period.Choose the amount of time desired.When the appliance is started with "I" button,a short acoustic signal will sound and the delay time on the display will blink ,indicating that the countdown has begun.

After the time has elapsed,the cycle will start.

NOTE:

During the delay period ,it is preferable not to change any of the settings.

a)If it is necessary ,all of the settings must be cancelled by press- ing the ON-OFF button (A) to indicate that all of the settings have been cancelled.

At this point,all of the steps for"Setting the Wash Cycle with a delayed Start Time" and "setting and Starting a Wash Cycle"must be repeated,following the instructions contained in the corre- sponding sections.

b)If the door is opened during the delay period, the indicator will blink and acoustic signal will sound, and the countdown will stop. It will begin again when the door is closed .

Wash Cycle adjustment Buttons

1/2 load Button

This button(see "close-up View - Control Panel",letter"C") make it possible to wash dishes using only the upper rack if there are not enough dishes for a full load.This will allow you to save on water and eletrical energy. It can be used before setting any of the wash cycle, except for the intensive cycle ( if included in the wash cycle table). Please keep in mind that the amount of deter- gent should also be cut in half.

GB

.6.