
FAQ
Phenomenon |
|
| Remedy | |
|
|
| ||
| No water supply or water pressure | Check | ||
No water | is too low |
| ||
Water use point is blocked or hot | Check and clear | |||
| ||||
| water valve is closed | |||
|
| |||
|
|
|
| |
| 1 | Hot water access close | Check and open | |
|
|
|
| |
| 2 | Temperature not set to desired | Calibrate the heater according to the | |
|
| setting | operation instructions in the manual | |
|
|
|
| |
Cold outlet water | 3 | Heating time limit and setting | Calibrate the heater by referring to | |
the operation instructions in the | ||||
|
| temperature not obtain | ||
|
| manual | ||
|
|
| ||
|
|
|
| |
| 4 | Defective elements | Contact with service department | |
| when 1 , 2 and 3 are excluded. | |||
|
|
| ||
|
|
|
| |
Not heated to | 1 | Whether the current function | Calibrate the heater according to the | |
| is set to the proper mode and | |||
desired temperature |
| operation instructions in the manual | ||
| temperature is set too low. | |||
|
|
| ||
water |
|
|
| |
2 | Excessive water pressure | turned down | ||
|
|
| ||
|
|
| ||
temperature of water | Inconstant water pressure | turned down or use with constant | ||
|
|
| water pressure | |
Incapable of startup | 1 | No power to heater | Check power socket | |
|
|
| ||
|
| Contact with service department | ||
or display not lit | 2 | Defective elements | ||
when 1 is excluded. | ||||
|
|
| ||
|
|
| ||
Display E1 | Faulty line | Contact with service department | ||
|
|
|
| |
| 1 |
| Power on after disconnection when | |
|
|
| ||
Display E2 |
|
|
| |
2 | Defective elements | Contact with service department | ||
| ||||
| when 1 is excluded. | |||
|
|
| ||
|
|
|
| |
| 1 | Room temperature lower than | when ambient temperature more | |
|
| |||
Display E3 |
| than | ||
|
| |||
| 2 | Defective sensor | Contact with service department | |
| when 1 is excluded. | |||
|
|
| ||
|
|
|
|
0040502425
V
Spa Water Heater
User's Manual
ES15V-P2
ES25V-P2
ES35V-P2
SPEED SET TIMER
SPEED TIMER
SET
Please read this manual before usage. Retain it for future reference.
Safety warning (Read carefully before use)
Meanings of icons |
| These are actions |
| These are matters |
|
| |||
These are |
|
| ||
actions which |
| which must be |
| for which attention |
Forbidden are forbidden |
| Warning carried out |
| CAUTION is required |
Installation • Use
Installation
(Figure 1) for installation reference only.
If the water heater emits an unusual smell or a burning smell, please disconnect the power supply immediately and call the service center.
This mark is the designation
for
Water Heater Company,
which indicates the use of
the company's patented technology inside the product. It ensures you a safe bath while monitoring whether your house ground wire is live or not all the time. If this mark is lit, it indicates your house ground wire was come live (poor grounding and live). In this case, please immediately stop use and disconnect the power, and remember not to touch any electric applicance in your house.
At the same time, immediately contact
Take care not to be scalded by hot water.
• | Do not touch the valve and pipe for hot |
CAUTION • | water supply. |
Please feel the water temperature before | |
| use. Use only when the temperature is |
| ideal for you. |
Do not set at outdoor places.
Forbidden
Do not install the water heater in the conditions in which ice could form. Ice formation will cause the water
Forbidden container and piping to crack, leading to scalds and water leakage.
Do not connect or disconnect the power supply while your hands are wet.
Hot water |
|
outlet | Safety valve |
|
|
| Cold water |
|
|
| inlet |
Hot | Cold |
| Shower |
water | Mixing | head | |
water |
| ||
outlet | outlet | Valve |
|
valve | valve |
|
|
Installation must be made by installers of or designated by our company
1 Make 2 holes Φ 12mm, 65mm deep in wall with an
impact drill according to the drawing of the external | Wall rack |
| |
dimensions (See Figure 4). |
|
2Take out all accessories in packaging liner, unpack
one hook, sleeve the ring end of the connection lines | Expansion | |
among the accessories into the hook tightening end | ||
hook | ||
and assemble the hook well. |
| |
3 | (Figure 2) |
management company for professional
Forbidden
right hole).
Extended connection line
| Warning | |
| personnel shall not carry out | |
| unauthorized repair, maintenance, |
|
Forbidden dismantling or |
| |
| the heater. |
|
| Be sure to use independent socket | Forbidden |
Earthing and earth it reliably. |
| |
| In case the power cord of the | Forbidden |
| water heater is damaged, be sure | |
|
| |
Warning | to have it replaced by after service |
|
technicians with special cord |
|
Warning
If you do not need to use the heater |
|
for a prolonged period, please cut | Warning |
| |
CAUTION in the heater in accordance with |
|
the instructions in the chapter on |
|
cleaning and maintenance. | Forbidden |
|
1
Check if the ammeter and the diameter of the wires are in accordance with the rated current of the water heater. If necessary, please have it checked by an experienced electrician.
Do not drink hot water from the heater or use it for similar purposes.
Do not spray water or steam onto the heater.
Please take precautionary measures during cold weather so as to prevent the heater from being frozen.
reliable wall.
Do not install at places without sewage.
4Lift the water heater and hang it with wall rack corresponding to the two hooks. Insert the connection spacer led from the rear shell wall rack of the heater into the connection terminal of the line on the hook (See Figure 2).
appropriate locations on inlet and outlet pipes respectively. Find the location requiring hot water supply. Connect inlet pipe, outlet pipe and city water pipe respectively to the use point for hot water. Fill the tank with water to check whether there is any leakage. It must be re- connected if there are signs of water leakage.
Warning: Do not release your grip unless the wall rack is securely hung on the hook. Otherwise the heater may fall and cause personal injury or property damage.
Installing safety valve
Connect the safety valve to the water inlet by following the direction of its arrow (the arrow should point towards the heater). The safety valve’s rated pressure is 0.80MPa and its connection is G1/2. Once power is connected and the water is being heated, the water inside the water tank will expand. In order to relieve the water pressure inside, a very
safety valve. The
Please connect the drain hose to the safety valve. Connect one end |
|
of the hose to the safety valve vent and the other end to the sewage |
|
drain. The hose can be cut short or extended as necessary. The hose |
|
shall be installed as inclined downward. | Connect to drain hose |
2