Install the water inlet hose
Confirm the water faucet
Water faucet,suitable | Water faucet,not suitable |
Outlet end surface |
|
>10mm |
|
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.)
water inlet hose jointer |
|
|
Slider |
| Screw |
|
| |
Screw knife |
| Sign plate |
| Bushing | |
Lock level |
|
|
water inlet hose |
|
|
Figure 1 | Figure 2 | Figure 3 |
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 4 | Figure 5 | Figure 6 |
| 3 "PROCESS"button |
|
|
PROCESS | You can choose one or more process among soak, wash, rinse, spin. | ||
The button is invaid if you choose QUICK or | TUB DRY | program. | |
| You can not choose soak process if you choose | WOOL | program. |
| 4 | ||
| |||
| Press the | ||
| |||
| flickers. About 3 seconds later, you can change the program | ||
by pressing "+" or " " button, to adjust reserved time (hour), | |||
|
|
| |
| soak time (minute), washing time (minute), spinning time | ||
| (minute) or rinsing times (number of times) . When the time or | ||
| number of times is 0, it means you cancel all the functions the | ||
| flicker lights associated with. |
|
|
| When choosing the "quick" program, you can add or reduce | ||
| the reserved time. Choosing the "wool" program, you can add | ||
| or reduce the reserved time but cannot change the washing, | ||
| spinning time and rinsing times, it means the washing time, | ||
| spinning time and rinsing times are defaulted time, times or | ||
| zero. When choosing the "Tub dry" program, the "Self- | ||
| Program" and "+" |
| |
| When choosing the "memory" program, after using the self- | ||
| program, the washing machine will remember the programs | ||
| you set this time when you use it next time. | ||
|
|
|
|
5 "WATER LEVEL"button
During standard programs, the washing machine can detect the laundries automatically. After detection, it will set the water level to suitable valve automatically among the water level "LOW","MEDIUM" ,"HIGH"and "MAXIMUM".
.
You can also set water level by yourself. After the machine is started, it will not set water level automatically. You shall push the"START/PAUSE" button to make new setting.
WATER | If there's water inside the tub, the machine can not detect the laundries and will display water | |
level "MEDIUM" .If wet aundries are put in, it may display water level "MAXIMUM" . | ||
LEVEL | ||
|
If "QUICK" program is selected, it will display water level "LOW". The water level can not be adjusted.
During operation of wash , rinse and soak program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of the different moisture level of the laundries.
