Haier XPB72-0713S, XPB72-0714D, XPB72-0715S

3. Run the foam-removing spinning.

(a) Open the outer cover of the spin tub.

(b) Set the water-filling selector control

rod at the "SPIN" side. Fill water for

about 1 minute. It the water quantity

filled is too large, the water may flow out

from the wash tub side. Please twist the

water tab to limit the water filling.

Spin for 1-2 minutes.

Put the laundries into the spin tub evenly and smoothly.

Spin

(a) Put the gland in properly.

Please put in the gland properly even if the laundries quantity is small.

(b) Close the inner and outer cover of the spin tub.

Midway spinning

Outer cover of

The spin tub

Inner cover of

The spin tub

Push

Proper The lau ndries

are slanting

Proper No glan d

Push

Gland

WASH SPIN

Installation and adjustment

Please install and adjust the machine according to the requirement of

the manual. It is very important to your security and correct operating

the machine.

Install the lint filter

After opening the package, please take

out the lint filter from the document bag,

install it to the overflow filter of the wash

tub. See to the figure.

The drainage shall be smooth with the

drain hose.

1. The height of the drain hose shall be

less than 10cm, or the drainage will

not be smooth enough and cause

incomplete drainage.

2. Do not tramp or press the drain hose.

3. If the drain hose is too long,

cut it at mid point. To make

smooth drainage, cut the

front end of the ho se

slantingly.

4. If extra drain hose is needed, please

make separate purchase. The inner

diameter of the extra hose shall not

be less than 30mm, and the length

shall not exceed 1.5m.

If the extra hose is too long, cut it

either at point A or B.

Usage of the drain hose

> 30mm

<1.5m

<10cm

A B

Overflow filter

Lint filter

Washing sequence

1. Water fill selection

(a) Set fill selection to 'Wash

side'. (Figure 1)

(b) Adjust water level rod to a

position as needed.

2. Fill wa ter and add disolved

powder detergent until water

reaches a suitable level. (Figure)

2) Begin to wash to dispense

detergent uniformly.

3. Put i n the wash load, and

supplement water as necessary.

4. Wash selector knob

Sele ct the washi ng sp eed

accord ing to th e laundr ies.

(Figure 3)

5. Select the washing time

Sel ec t th e wa sh in g ti me

accord ing to th e laundr ies.

(Figure 4)

6. After washing, the buzzer will

ring.

Set the "WASH SELECTOR" at

"DRAIN". (Figure 5)

Wash

Figure 2

*WASH T IME R

OFF

WASH SELECTOR

Figure 5

DRAIN

STRONG

STANDARD

WASH SELECTOR

Figure 3

DRAIN

STRONG

STANDARD

#SOAK T IME R

Figure 4

OFF

Figure 1

SPIN

WASH

Water inlet

Water filling

control handle

SPIN

WASH

SPIN TIMER

OFF

Overflow sign

Spin timer

(to set to below 1 minute,

first set to 2 minute then

turn it back. it can increase

the service life of the timer).

* For the model with Wash Timer.

# For model with Soak Timer.

Wash selector

(standard wash speed,

strong wash speed)

WASH SELECTOR

DRAIN

STANDARD

Wash/Soak timer

(To set to below 2 minute,

first set to 6 minute then

turn it back. it can increase

the service life of the timer).

WASH/SOAK TIMER

OFF

STRONG

Safety precautions

Petrol

Thinner

Do not stretch hands into the

working machine. It is dangerous

even if the rotation is slow. Take

special care of the children.

Handicapped or children without

care shall not use the machine.

Do not put any hot or heavy items

(such as the kettle with hot water) on

the washing machine.

Do not decompose, repair or alter

the machine by yourself.

Keep the machine away from direct

sunlight and heat source like the

heater.

Do not wash laundries with volatile

materials (such as thinner, petrol

etc.).

Please put down the drain hose before washing, and connect the water inlet

pipe properly.

It is suggosted to use foamless washing powder.

Please don't use t he washer in the environment below 0 C.If t he washer is

bleow 0 C, the washer's water inlet system a nd draining system will be

frozen, then result in th e damaged of the whole m achine. If the washer has

below 0 C, please be sure to ensure the washe r is placed under the room

temperature for 2-4 hours a nd then use.

To protect your laundry and washing machine,

please take out all coins, buttons, sand, hairpins and

other foreign materials from the clothes before

washing.

The musts in washing

Usage of the detergent

Fill water to decided level.

Dilute the whitener with

container. Pour it slowly into

the washing tub.

Avoid usin g whitene r on

laundries with color or pattern

as they are prone to lose color.

The whitener shall not touch

the laundries directly.

Refer to the user's manual for

the usage and quantity of the

whitener.

For powder whitener, please

dissolve it before using.

It is suggested not to use high

sudsing detergent.

•

Direct dissolved in the machine:

1. Fill small quantity of water.

2. Add the powder. Run for 30

seconds to dissolve it completely.

3. Put it in the laundries. Select

suitable water level.

The instant dissolving of the

washing powder.

1. Prepare warm water of 30C and

a container.

2. Add the powder while stirring to

fully dissolve it.

The powder is more prone to pollute

the laundries than the detergent.

Therefore please use it with proper

quantity.

Dosage of different washing powder

is different. Please refer to the

instruction of the washing powder

for the detail dosage.

•

The capacity of washing and spinning of

the machine refer to the largest weight of

the standard laundries under dry condition

that can be washed or spinned in one time.

Laundries quantity in one washing cycle

shall be lower than the rated capacity.

The thickness, size, type of the cloth will

influence the actual washing capacity. It is

suitable to put in reasonable amount of

laundries and the laundries can be turned

round in washing for one time washing.

Do not select "Maximum" water level for

laundries less than 1.0kg, so as to avoid

splashing of water.

How to use the whitener How to use the washing powder

•

Safety precautions

In case the washing machine is

installed on ground with carpet, do not

block the ventilation hole with carpet.

Do not put the machine at damp

place like the bathroom . Never wash

it w ith water. Do n ot place wet

laundries on the control panel.

Do not use water hotter than 50 C.

Do not let the machine share one receptacle

with other electric appliances. If the power plug

is damaged, or the plugging into the receptacle

is loose, do not use the plug any more.

Do not wash water-pfoof laundries

like the raincoat, bike covers etc. to

avoid abnormal vibrations in spinning.

Please insert the power cord into

special receptacle with rated

voltage. Be sure to use single-

phase three pins receptacle.

The ear thing terminal of the

receptac le must be eart hed

reliably. If possible, please adopt

electric leakage protector.

When the machine is being used

normally, please put the power

plug at the location easily to be

inserted and extracted by hand.

Be sure to pull the plug off when

there's power failure, or the

mac hin e is b ein g mo ved ,

cleaned of when it is idle.

If the power cord is bad, to avoid risk it is required to replace it by the

technicians of our special shop or the after-sale service department.

Keep the pin of the power plug clean.

Ventilation hole at

the bottom of the

washing machine

50 C

Preparation before washing

Preparation before washing:

1. Connect the water inlet hose.

2. Confirm that the washing machine is earthed

reliably. Then insert the power plug into the

receptacle. Do not connect the earth terminal to

the gas pipe and tap water pipe.

3. Put down the drain hose.

4. Slanting or uneven ground may result in

unstable wor king or abnormal noise. Please

make the machine stand horizontally.

Check if Clear the Tie the long The quantity of When the pulsator

the laundries pocket. Take strips; fasten the laundries is running, the buttons

has any out the coins, the buttons; shall not be too of the laundries may

special sand, hairpins close zippers. large. Stretch cause noise. For the

requirement etc. and loosen the sake of discretion,

for washing. laundries before please wash the

(fabric putting them in laundries with buttons

should the tub. separately (along with

be marked laundry washing bag).

machine

wash)

a. Check if the laundries are applicable for washing in machine.

b. Divide the laundries that are not colorfast from other laundries.

c. Soak those laundries which absorb water with difficulty, by hand.

d. For those laundries with heavy soil, please first remove the dirt like mud or

dust. for the parts with heavy soil, please apply detergent on them in

advance, which can make it easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn it

over before putting in machine.

f. Do not put the laundries polluted by chemicals into the washing machine

directly.

Pay attention to followings before washing the laundries

Names of the parts

Outer cover of the spin tub

Inner cover of the spin tub

Spin timer

Spin tub

Cabinet

Major frame

Base frame

Wash selector

Wash/Soak timer

Control panel

Overflow filter

Water level adjusting lever

Pulsator

Wash tub

Drain hose

Wash tub cover

Water-filling entrance

Valve cover

Protecting cover

All illustrations in this manual are given for reference only. Your

products and acces sories may show differen ces from these

illustrations due to our continuous improvement.

Notes:

Meaning and description of the symbols

Contents marked with that symbol are

related to the safety of the product and the

persona l safety of t he users. Ple ase

operate in strict conformity to the contents,

otherwise it may cause damage of the

machine or injure the personal safety of

the user.

Contents marked with that symbol are

actions forbidden to perform. Performing of

those actions may result in damage of the

machine or injure the personal safety of the

user.

Please check if the power receptacle has good earthing condition

before using to guarantee your safety.

Warning sign

Forbidding sign

•

Figure 1

Drain hose

fixing hook

Figure 2

Drain hose

fixing hoo k

Pull outwa rds

slightly

Side sectional view

Fixing ho ok

install ation h ole

Drain hos e

Take off

the drain h ose

Figure 5 Figure 6

How to change the direction of the drain hoses

Install the water inlet hose; Select the water level

Figure 1 in dicates the ex f actory

installation position of the drain hose.

Take off the drain hose from the hanging

hole of the cabinet. Pull the drain hose

fixing hook outwards gently to take out

the drain hose from the two fixing hooks.

(As per figure 2)

Rotate the drain hose fixing hook for 90

to take it out from the installation hole (As

per Figure3).

Install the two drain hose fixing hooks

taken out into the installation hole at the

other side of the base frame (to aim at the

installation hole accurately you can lean

the washing machine forward slightly).

Then rotate for 90 (As per Figure 4).

Pull the fixing hook outwards slightly.

Inlay the drain hose into the fixing hooks

reliably along the groove at spin tub side,

and make it extendtowards spin tub side.

Then hang the drain hose into the

hanging hole at the spin tub side. (As per

Figure 5).

Take out the drain hose from the fixing

hook. Extend it from the near side (When)

the drain hose is extended from the rear

side, it can be hung on the point for drain

hose at the two sides of the cabinet.) (See

to Figure6).

•

Extend the drain hose from the side of spin tub

Extend the drain hose fro m the rear side

Insert the water inlet hose into the water-

filling entrance on the control panel directly-

(pull it out to dismantle it)

Select water level according to the quantity

of the laundries.

Set the water level adjusting lever to

needed line.

Figure 4

Insert the fix ing hoo k into th e

installati on hole u pward s

Rotate the fix ing

hook for 90ｰ

to fix it

Figure 3

Take off the fixing

hook downwar ds

Rotate the fix ing

hook for 90ｰ

Water inlet hose

Water inlet

Max

Med

Min

Maximum

Medium

Minimum

Water level

indicator

Contents

• Names of the parts 1

• Safety precautions 2

• Installation and adjustment 4

• Preparation before washing 6

• The musts in washing 7

• Usage of the detergent 7

• Washing sequence 8

• Disposal after washing 12

• Trouble-Shooting * Answer to question 14

• Packing list *Specification 16

Gripper