Trouble shooting 
Answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or
|
| Phenomena | The reason | How to settle | |||||
|
| Buzzing upon reservation starts, |
| The top lid is not closed |
| Close the top lid | |||
|
| Nixie tube indicates "E0" |
|
| |||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| No or slow drain, nixie tube |
| Is the drain hose put down? |
| Put down the drain hose. | |||
|
|
|
| Open and close the top lid once. | |||||
|
| indicates "E1" , buzzing. |
| Is the drain hose blocked |
| ||||
|
|
|
| Clean the foreign material. | |||||
|
|
|
|
| by foreign material? |
| |||
|
|
|
|
|
| Open and close the top lid once. | |||
|
|
|
|
|
|
|
|
| |
|
| Running pauses during spin, |
| The top cover leaves open |
| Close the top lid | |||
|
| nixie tube indicates "E2", |
|
| |||||
|
| buzzing |
|
|
|
|
|
| |
|
| Safety switch actuates, not spin, |
| Are the laundries put |
| ||||
|
| (after |
| slantingly? |
| top lid.Level the machine in right | |||
|
| nixie tube displays "E3", buzzing |
| Is the machine slanting? |
| position. | |||
|
|
|
| Open and close the top lid once. | |||||
|
|
|
|
|
|
|
|
| |
|
| No or slow water filling not |
| The water tap is not open |
| Open the water tap. Push the | |||
|
|
| The water inlet valve is blocked |
| "Start/Pause" button. | ||||
|
| reaching the level in 15min , |
|
| |||||
|
|
|
| Clean the water inlet valve. | |||||
|
|
|
|
|
|
| |||
|
| nixie tube indicates "E4", |
| The water pressure is too |
| ||||
|
|
|
| push the "Start/Pause" button. | |||||
|
| buzzing |
| low and | the current is |
| Wait for the normal water pre- | ||
|
|
|
|
| too small |
| ssure before use. | ||
|
| Poor or no waterfall flow |
| If the nozzle is choked with |
| Remove the foreign bodies | |||
|
|
| foreign bodies |
|
| ||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Is there power failure? |
| Use it when the power is on. | ||
|
|
| Not wash |
| Is the power plug loose? |
| Insert the power plug tightly. | ||
|
|
|
|
|
|
|
|
| |
|
| The machine |
| Does the water level arrive at the |
| Affusion to the set water level. | |||
|
|
| set water level? |
| |||||
|
| does not act |
|
|
|
| |||
|
| Not spin |
| Is the power plug loose? |
| Insert the power plug tightly. | |||
|
|
|
|
| |||||
|
|
|
| Is the top lid closed? |
| Close the top lid | |||
|
|
|
|
|
| ||||
|
|
|
|
| Are the laundries put orderly? |
| Put the laundries orderly. | ||
|
| There's abnormal sound |
| Is the machine slanting? |
| Level the machine properly. | |||
|
| inside the machine |
| Are the laundries slanting in |
| ||||
|
|
|
|
| spinning? |
|
|
|
|
|
| The water faucet leaks |
| Is the jointer screw of the water |
| Fasten the jointer screw | |||
|
|
| inlet hose is loose or twisted |
| properly. | ||||
|
|
|
|
|
| ||||
|
|
|
|
| awry? |
|
|
|
|
|
| Common phenomena |
|
|
|
| |||
|
| Phenomena |
|
| Explanation |
| |||
|
| The spinning is intermittent when it starts. |
| Balance the laundries to avoid slanting. | |||||
|
|
| |||||||
|
| Push the "Procedure selection" button to |
| The program is setting the drain time. Some time is | |||||
|
| select "Spin", but it doesn't work. |
|
| needed before it starts spinning. | ||||
|
|
|
|
| |||||
|
| There may be some water flowing out of |
| It is the water remained in the factory inspection of | |||||
|
| the drain hose in the first use of the machine. |
| performance. |
| ||||
|
|
|
|
| |||||
|
| While water filling in wash and rinse, the |
| To prevent splash during water filling. | |||||
|
| pulsator pauses rotation |
|
|
|
|
| ||
|
|
|
|
|
|
|
| ||
|
| Wash pauses |
|
| Supplementary water filling 48 s after | ||||
|
|
|
| sensor tests cloth material. | |||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
15
