UNPACKING

When unpacking, make sure the following accessories are included: blade adjustment gauge, “T” wrench, screwdriver, dust collection outlet, push block and fence angle gauge.

INSTALLATION

1.The Jointer Planer should be installed permanently to a sturdy workbench for best results.

Each corner of the base should be fixed securely to the surface by using bolts, nuts and washers.

2.If you wish your Jointer Planer to be portable, the following mounting instructions should be followed. Use a solid piece of wood (not particle board) with a minimum thickness 3/4”. This base must also be at least 36” L x 20”W. Bolt the Jointer Planer to the base with bolts, nuts and washers. When using the machine, clamp it firmly to a stable and secure location for best results.

WARNING: Check blade setting and tightness before initial use.

ADJUSTMENTS & OPERATIONS

Cutting Depth Adjustment

CAUTION! Turn the machine off, unplug and wait until blades reach a complete stop before adjusting the cutting depth!

1.To decrease the cutting depth, turn the depth control knob (67) clockwise; this will raise the infeed table. To increase the cutting depth, turn the dial counter-clockwise.

CAUTION! Never adjust the cutting depth so that it exceeds 1/8”!

2.To check your cutting depth adjustment, first put the depth adjustment gauge plate on the outfeed table and allow it to hang over the infeed table. Use a ruler with the proper graduations and measure from the bottom of the gauge to the top of the outfeed table. This will indicate your cutting depth.

Fence Adjustment:

1.To adjust, angle your fence angle (0o-45o), loosen both fence angle adjustment levers (52). Adjust to desired angle to according to the scale and tighten both levers.

2.To adjust the position of the fence on the table, loosen both fence adjustment knobs (39). Adjust to desired position and then tighten. This should be done when you desire only a certain section of the board to be planed or jointed.

3.When you have completed adjusting the fence, be certain that the auxiliary blade guard (45) is over the cutter head assembly.

Replacing and Adjusting Blade:

CAUTION! Turn the machine off, unplug and wait until blades reach a complete stop before adjusting the cutting depth!

NOTE: Both blades must be replaced simultaneously or else the balance will be affected.

1.Loosen the two screws (54) holding the belt cover (29) on and remove it.

2.To fix the cutter head assembly (58) in place, pull the “U” shaped lock pin (36) out and reposition it in the upper hole on the back of the machine. (See associated label on the back of the Jointer Planer.) Rotate the drive belt (28) by hand until assembly “clicks” into place. A small hole is provided in the pulley (73), which will accept a probe for easier turning.

REV 12/06

SKU 34434

For technical questions, please call 1-800-444-3353.

Page 5

Page 4 Page 6
Page 5
Image 5
Harbor Freight Tools 34434 operating instructions Unpacking
Page 4 Page 6

34434 specifications

Harbor Freight Tools offers an impressive range of tools and equipment for both professionals and DIY enthusiasts, and among its popular products is the 34434. This versatile tool has garnered attention for its reliability, affordability, and user-friendly features that cater to a varied audience.

The Harbor Freight Tools 34434 is a 20-gallon parts washer that provides an efficient and effective solution for cleaning automotive parts and components. Designed for convenience and performance, it is ideal for mechanics and hobbyists alike who need to maintain and restore their tools.

One of the key features of this parts washer is its large capacity. The 20-gallon tank can accommodate a wide variety of parts, allowing users to clean multiple items at once. The spacious interior reduces the need for multiple wash cycles, saving both time and effort.

Additionally, the 34434 includes a powerful pump system that circulates cleaning solvent through a drain hose and back into the tank, ensuring that contaminants are effectively washed away. This constant circulation helps to maintain a clean working environment and prolongs the life of the cleaning solution, making it a cost-effective option for users.

The design of the parts washer prioritizes ease of use. It features a built-in work surface, which allows users to easily place their parts for washing, while the adjustable spray nozzle provides users with control over the flow and intensity of the cleaning solution. This adaptability ensures that delicate parts can be cleaned thoroughly without the risk of damage.

Safety is also a significant consideration in the design of the 34434. It includes a splash guard to prevent cleaning solvent from spilling out of the tank, as well as an integrated lid that helps to limit fumes from escaping. These features work together to create a safer working environment.

In conclusion, the Harbor Freight Tools 34434 is an excellent investment for anyone in need of an efficient and reliable parts washer. With its ample capacity, powerful cleaning capabilities, user-friendly design, and safety features, it stands out as a go-to choice for automotive cleaning tasks. Whether for DIY projects or professional use, this tool meets a variety of needs, making it a valuable addition to any workshop.
Top Page Image Contents