|
|
|
| 4. | Always assume the tool contains | |
|
| Air source | ||||
a. |
| Never connect to an air |
| fasteners. |
| |
| 5. | Do not point the tool toward yourself | ||||
|
| source that is capable of | ||||
|
| exceeding 90 PSI. Over |
| or anyone whether it contains fasten- | ||
|
| pressurizing the tool may |
| ers or not. |
| |
| cause bursting, abnormal operation, | 6. | Do not actuate the tool unless the | |||
| breakage of the tool or serious injury | |||||
|
| tool is placed firmly against the work- | ||||
| to persons. Use only clean, dry, |
| ||||
|
| piece. |
| |||
| regulated compressed air at the rated |
|
| |||
| 7. | Respect the tool as a working imple- | ||||
| pressure or within the rated pressure | |||||
| range as marked on the tool. Always |
| ment. |
| ||
| verify prior to using the tool that the | 8. | No horseplay. This tool is not a toy | |||
| air source has been adjusted to the | |||||
|
| and can be deadly if misused. |
| |||
| rated air pressure or within the rated |
|
| |||
|
|
|
| |||
| 9. | Do not load the tool with fasteners | ||||
b. | Never use oxygen, carbon dioxide, |
| when any one of the operating con- | |||
| trols, such as the Trigger or Safety | |||||
| combustible gases or any bottled |
| ||||
|
| Nosepiece, is activated. |
| |||
| gas as an air source for the tool. |
|
| |||
|
|
|
| |||
| Such gases are capable of explosion | 10. | Do not remove, tamper with, or other- | |||
| and serious injury to persons. |
| wise cause the tool operating controls | |||
| SAVE THESE |
| to become inoperable. |
| ||
| 11. | Do not operate the tool if any portion | ||||
| INSTRUCTIONS. | |||||
|
| of the tool operating controls is inop- | ||||
|
|
|
|
| erable, disconnected, altered, or not | |
|
|
|
|
| working properly. |
|
| SPECIFIC SAFETY |
|
| |||
| 12. | Disconnect the tool from the air sup- | ||||
| INSTRUCTIONS | |||||
|
| ply when: |
| |||
|
|
|
| |||
1. Operators and others in work area |
| a. Unattended. |
| |||
| MUST wear |
| b. Performing any maintenance or | |||
| goggles with side shields during |
| repair. |
| ||
| use. The employer is responsible to |
| c. Clearing a jam. |
| ||
| enforce the use of eye protection by |
|
| |||
|
| d. Moving the tool to a new location. | ||||
| the operator and others in the work |
| ||||
| area. |
|
| 13. | Do not make any modifications to this | |
|
|
|
| |||
2. Keep fingers away from trigger |
| tool. |
| |||
| when not driving fasteners to | 14. | Refer to the tool maintenance instruc- | |||
| avoid accidental firing. | |||||
|
| tions for detailed information on the | ||||
|
|
|
|
| ||
3. Choice of triggering method is im- |
| proper maintenance of the tool. | ||||
| portant. Check manual for trigger- | 15. | Fire fasteners into an appropriate | |||
| ing options. | |||||
|
| work surface only. Do not attempt to | ||||
|
|
|
|
| ||
SKU 66995 | For technical questions, please call | Page 5 | ||||
