MAS SYSTEM

Installation

1.Carefully unpack the controller, amplifier, speakers, FM antenna, DAB antenna (MAS 111 systems only), analog audio cable, ribbon cable, detachable AC power cord, The Bridge IIIP dock for iPod, remote control and batteries.

2.Open the battery compartment of the remote control by firmly grasping the portion of the remote that has the Harman Kardon logo and pulling it downward. Install the batteries in the remote control, following the “+” and “–” symbols in the battery compartment to maintain the correct polarity.

CAUTION: Danger of explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type.

3.With the controller stacked on top of the amplifier, carefully insert one end of the ribbon cable into the connector on the rear panel of the controller, and the other end into the corresponding connector on the rear panel of the amplifier.

4.Connect the FM antenna to its terminal. The system requires a female connector on the antenna. For MAS 111 systems only, connect the DAB antenna to its terminal.

5.Install The Bridge IIIP (included with MAS 101/MAS 111 systems only) dock for iPod (iPod is not included).

a. Holding the cable with the wider part of the connector at the bottom, gently squeeze the tabs on each side as you insert it into the connector on the rear panel of the controller.

b. Place the black insert in The Bridge IIIP, making sure to push it all the way down. See Figure 1.

NOTE: Do not place an iPod in The Bridge IIIP unless both the black insert and a dock adapter are installed. Otherwise, the iPod will not connect properly, and both

Figure 1:

Docking an iPod

in The Bridge IIIP

it and The Bridge IIIP may sustain damage that is not covered by the warranty.

c. Locate the dock adapter that was included with your iPod, or select one of the included dock adapters by referring to Table 1. If your iPod is an older model that does not appear in Table 1 and that did not include an adapter, contact Apple, Inc. to purchase one.

Place the adapter in The Bridge IIIP insert, as shown in Figure 1.

d. Remove the iPod from any case, and dock it in The Bridge IIIP, as shown in Figure 1.

6.The MAS system features eight audio inputs for other devices, such as portable players. This step is optional, and may be skipped if you have no external devices.

If your player has:

tA stereo 3.5mm analog audio output or headphone jack: Plug an analog audio cable (not included) into the output or headphone jack and the front mini-jack, which is located on the right side of the controller.

tPair of RCA-type analog audio outputs: Plug one end of a two-conductor interconnect cable (one cable is included; purchase additional cables for other devices) into the player, and the other end into the TV or Auxiliary Input jacks on the rear panel of the MAS system. Use the same-color connector for each channel (usually red for right, and white or black for left).

tIf your device is a turntable with an MM-type cartridge, connect its outputs to the Phono (MM) Inputs on the rear panel of the controller. If it is another type of turntable, do not connect it to the MAS system without using a separate phono preamp, available from electronics outlets. Do not connect a turntable to another set of inputs without using a phono preamp.

tOptical or coaxial digital audio S/PDIF output: Plug one end of the digital audio cable (not included) into the player, and the other end into one of the Optical or Coaxial Inputs on the rear panel of the MAS system.

Remember to select the correct analog or digital input as the source by pressing the Line In or Digital In Source Selector on the remote.

7.To make analog or digital audio recordings, connect the Coaxial Digital Output or the Line Output on the rear panel of the controller to the corresponding input on an audio recorder (not included). The MAS system can convert analog or digital signals to the other domain.

8.Place the left and right loudspeakers as desired. It is recommended that the speakers be placed so as to form an equilateral triangle with the usual listening position. Thus, each speaker will be the same distance from the other speaker as it is from the listening position.

Place the speakers at about the same height as the listener's ears.

Connect one end of each included speaker cable to the terminals on the speaker, and the other end to the terminals on the amplifier. To ensure proper performance and bass response, make sure to preserve the correct polarity by connecting the positive terminals (colored red) to each other and the negative terminals (colored black) to each other.

9.Plug all power cords for the MAS system and any external sources into unswitched AC outlets.

Table 1 – Select the Correct The Bridge IIIP Insert

The Bridge IIIP Insert

iPod Model

 

 

NANO

iPod nano, 1st and 2nd generations

 

 

5G (VIDEO 60GB)

iPod, 5th generation (60GB, 80GB) and

 

iPod classic (160GB)

 

 

5G (VIDEO 30GB)

iPod, 5th generation (30GB) and iPod

 

classic (80GB)

 

 

13

iPod nano, 3rd generation and 4th

 

generation

 

 

12, 14

iPod touch – install large bumper

 

 

10

Page 9 Page 11
Page 10
Image 10
Harman-Kardon MAS 101, MAS 111, MAS 102 owner manual Installation, Bridge Iiip Insert IPod Model
Page 9 Page 11

MAS 101, MAS 111, MAS 102 specifications

Harman Kardon, renowned for its high-fidelity audio products, offers a trio of integrated audio systems: the MAS 102, MAS 111, and MAS 101. These compact all-in-one solutions are designed to deliver exceptional sound quality while encompassing modern technological features.

The Harman Kardon MAS 102 is a versatile system that combines performance with user-friendly features. This model boasts a powerful amplifier with a robust power output, making it ideal for driving a range of speakers. The MAS 102 includes both analog and digital inputs, allowing for seamless connectivity with various audio devices, including CD players, turntables, and modern digital sources. Its integrated AM/FM tuner enhances its capabilities, providing access to a wide range of radio stations. The sleek design and intuitive remote control make it an attractive addition to any audio setup.

Moving on to the MAS 111, this model elevates the audio experience further with added functionality. It incorporates a unique digital signal processing technology that ensures clarity and precision in sound reproduction. The MAS 111 features a high-quality DAC (Digital-to-Analog Converter), which enhances audio fidelity for digital sources. This system also supports multiple formats, making it a versatile choice for music lovers who enjoy a variety of media. The built-in Bluetooth capability allows users to stream audio wirelessly from smartphones, tablets, and computers, while the USB input provides additional convenience for direct playback of music files.

The MAS 101, while simpler, remains a powerful contender in this lineup. It is tailored for those who appreciate straightforward functionality combined with premium sound quality. The MAS 101 features an efficient integrated amplifier and offers essential connectivity options, including both phono and line-level inputs. Its compact design makes it suitable for smaller spaces, yet it does not compromise on audio performance. The system delivers rich and immersive sound, catering specifically to vinyl enthusiasts with its dedicated turntable input.

In summary, the Harman Kardon MAS series—consisting of the MAS 102, MAS 111, and MAS 101—caters to diverse audiophile needs. Each model brings its own unique features and characteristics, ensuring that users can find the right system to suit their sound preferences and lifestyle. Whether you’re seeking advanced digital capabilities, seamless connectivity, or pure analog performance, the MAS series stands as a testament to Harman Kardon’s commitment to audio excellence.
Top Page Image Contents