Ramp Moving Instructions | Health O Meter 2600KL instruction

ASSEMBLY INSTRUCTIONS

Ramp - Moving Instructions

1.Remove the guardrail at the end of the platform by unscrewing 4 screws. (see Figure 3)

2.Fold the ramp on the platform surface.

3.Gently tip the scale over and place with handrail on the floor.

4.Remove the screws attaching 2 rubber bumpers on the side of the platform under the ramp attachment. Remove the bumpers. Install the rubber bumpers on the opposite platform side in the appropriate holes.

5.Release 4 screws at each ramp holder (2 screws at ramp side and 2 screws at the bottom of the ramp, close to wheel).

6.Remove the ramp from the ramp holders, then release all the screws to the end and remove ramp holders by pulling out slightly.

7.Install ramp holders in the same way at the opposite side of the platform, do not tighten screws.

8.Insert the ramp between ramp holders and tighten screws.

9.Install the guardrail by screwing 4 screws. Note: It is necessary to bore a hole in the mat to insert the screw in appropriate hole beneath the mat.

Figure 3. Ramp Moving

(refer to the Parts List on page 23 for details on parts followed by # ) NOTE: A second Ramp is available separately as 2600RAMP.

5

Image 6

Health O Meter 2600KL operation manual Ramp Moving Instructions

Contents

PRO Plustm Electronic Folding Wheelchair Scale Table of Contents Specifications Scale SpecificationsGeneral Assembly Instructions Assembly Instructions Ramp Moving Instructions SET UP Scale Opening and Folding Procedures Preparing the Scale for Use Replacing Batteries Operation Instructions Description Function Weight Display Mode MenuOnly applies to pound values, not the metric values Automatic Tare Tare WeightData Management Removing the Tare Enter Scale Settings Operation Instructions System Settings System Test User Settings Operation Instructions Cleaning MaintenanceMaintenance Disconnect the scale from the AC power source Troubleshooting Symptom Possible Cause Corrective Action Calibration Path Operator Action DisplayPage Parts List Description Qty What does the Warranty Cover? WarrantyLimited Warranty To get Warranty Service Table DES Matieres Precaution ET Prevention Specifications DE LA BalanceGeneralites Mode Dassemblage Mode Dassemblage Rampe daccès Instructions de retrait Installation Balance Instructions douverture et de pliage Remplacement des piles Préparation de la balance avant usage Mode DE Fonctionnement Touche Description Fonction Mode Daffichage DU Poids Menu Principal Tarage Automatique Poids DE LA TareGestion DES Donnees Retrait de la Tare Mode DE Fonctionnement Reglages DE LA Balance Mode DE Fonctionnement Reglages DU Systeme Test DE Systeme Reglages Utilisateur Mode DE Fonctionnement Nettoyage Déconnectez la balance du secteur CA Symptome Cause Possible Action Corrective Localisation DES Pannes Calibrage Action réalisée par lopérateur Message affichéPage Liste DES Pieces Pièce N Code Description Quantité Pour obtenir un service de garantie Garantie Índice Precaución Y Advertencia EspecificacionesEspecificaciones DE LA Balanza Instrucciones DE Montaje Tapa Trasera Instrucciones DE Montaje Rampa Instrucciones de Movimiento Configuración Balanza Procedimientos de Apertura y Plegamiento Preparando la Balanza para ser Usada Cambiando las Baterías Instrucciones DE Operación Ítem Descripción Función Menú Modo DE Presentación DEL Peso Tara Automática Administración DE DatosPeso Tara Removiendo la Tara Calculando EL BMI Configuraciones DE LA Balanza Instrucciones DE Operación Configuraciones DEL Sistema Prueba DEL Sistema Configuraciones DEL Usuario Instrucciones DE Operación Limpieza MantenimientoMantenimiento Desconecte la balanza de la fuente de energía CA Solución DE Problemas Síntoma Posible Causa Acción Correctiva Trayectoria DE Calibración Acción del Operador DisplayPage Lista DE Partes No. Llave Parte No Descripción Cd3 Garantía Garantía Limitada¿Qué Cubre la Garantía?