Healthrider HRTL17981 manual HOW to Program the Custom 1 and Custom 2 Programs

HOW TO PROGRAM THE CUSTOM 1 AND CUSTOM 2 PROGRAMS

The Custom 1 and Custom 2 programs are workout programs that you create. The programs control both the speed and the incline of the treadmill, and can be up to forty minutes long. The programs are stored in memory, and can be changed as many times as de- sired. Follow the steps below to create a program.

1 Insert the key fully into the console.

See HOW TO TURN ON THE POWER on page 9.

2 Select the Custom 1 or Custom 2 program.

To select the Custom 1 or Custom 2 program, the MANUAL indicator or a program indicator

must be flashing. If nec- essary, hold down the

STOP/PAUSE button for two seconds until the MANUAL indicator is flashing. Next, press the SELECT + or – button repeatedly until the Custom 1 or Custom 2 program indicator is flashing. Then, press the ENTER button. Indicators will appear at the bottom of the program display.

Note: When you are familiar with the console, you may go directly to step 5. While learning to use the console, please read all steps.

3 Enter your weight if desired.

When the Custom 1 or

Custom 2 program is selected, a weight setting will begin to flash in the

CALORIES/FAT CALO- RIES display. If your

weight is entered into the console, the CALORIES/ FAT CALORIES display will be more accurate.

If you do not want to enter your weight, or if you have already entered your weight, press the ENTER button. If you want to enter your weight, press the SELECT buttons. When the correct weight is shown, press the ENTER button.

4 Enter your age if desired.

See step 4 on page 10.

5 Press the START button or the SPEED + button.

A moment after the button is pressed, the walking

	belt will begin to move. Hold the handrails and
	begin walking.
6	Press the RECORD button and program the
	desired speed and incline settings.
	When the RECORD button is pressed, the Custom
	1 or Custom 2 indicator will begin to flash rapidly.
	Speed and incline settings can be programmed
	only when the indicator is flashing rapidly.
	Each program is divided into one-minute segments.
	One speed setting and one incline setting can be
	programmed for each segment. The speed setting
	of the first seg-
	ment is shown in	Current Segment
	the flashing
	current segment
	column of the
	program display.
	(The incline
	settings are not
	shown in the
	program display.) To program speed and incline
	settings for the first segment, simply adjust the
	speed and incline of the treadmill to the desired
	levels with the SPEED and INCLINE buttons.
	Every few times the SPEED buttons are pressed,
	one additional indicator will light or darken in the
	current segment column.
	When the first segment is completed, a series of
	tones will sound and the current speed and incline
	settings will be stored in memory. All settings
	shown in the program display will then move one
	column to the left, and the speed setting of the sec-
	ond segment will be shown in the current segment
	column. Program speed and incline settings for the
	second segment as described above. Repeat this
	procedure until you have programmed speed and
	incline settings for as many segments as desired.
	Programs can have up to forty segments.
	Note: To stop the program for a moment, press the
	STOP/PAUSE button. The displays will pause and
	the TIME display will begin to flash. To restart the
	program, press the START or SPEED + button.
7	Hold down the STOP/PAUSE button for two
	seconds.

When you have programmed speed and incline
settings for as many one-minute segments as
desired, hold down the STOP/PAUSE button for
two seconds. The speed and incline settings that
you have programmed and the length of the pro-
gram will be stored in memory. To use the program
again, see HOW TO USE THE CUSTOM 1 AND
CUSTOM 2 PROGRAMS on page 14.	13