E. Install Attic Insulation Shield

Warning! Risk of Fire! You MUST install an attic in- sulation shield when there is any possibility of insulation or other combustible material coming into contact with the chimney.

Do not pack insulation between the chimney and the attic insulation shield.

Failure to keep insulation and other materials away from chimney pipe could cause fire.

Do not offset chimney inside insulation shield.

Installation of a ceiling firestop is required

Refer to Figures 8.6 - 8.8.

Roll the shield around the chimney (if chimney is already installed) until you have a 3 in. (76 mm) overlap and the three holes on each side match up (large holes on top).

Insert three screws into the matching holes to form a tube.

Bend three tabs on the bottom of the tube inward to 90° to maintain chimney air space as shown in Figure 8.6.

Rest the insulation shield on the ceiling firestop below.

Bend the three short tabs at the top of the shield inward to 90° to maintain the 2 in. (51 mm) air space from the chimney.

Bend the remaining top tabs to just meet the pipe.

If you wish to make a custom shield or barrier, follow these guidelines:

Metal is preferred, although any material stiff enough to hold back the insulation can be used.

Warning! Risk of Fire! Use of cardboard or other materials that can deflect under humidity or other envi- ronmental conditions is not recommended.

The shield or barrier must be tall enough to extend above the insulation and prevent blown-in insulation from spilling into the cavity.

The shield should be affixed to building structure.

Maintain specified air spaces around chimney.

Check instructions and local codes for further details.

 

 

 

 

Bend remaining tabs

 

 

 

 

to rest against pipe to

Bend

 

inward

prevent insulation

90°

 

from falling in.

 

 

 

 

 

Insert three

 

 

 

 

screws

3 in. (76 mm) overlap

Figure 8.6 Prepare Attic Insulation Shield

 

 

Tabs bent in to

 

Pipe

rest against pipe

 

 

 

 

Attic Insulation Shield

 

 

17 in. (432 mm)

 

6 Tabs bent

diameter

 

in 90°

Ceiling Firestop

 

 

Insulation

Pipe

Insulation

13 in.

 

 

(330 mm)

 

 

Figure 8.7 Install Attic Insulation Shield Above the Ceiling

 

 

Tabs bent in to

 

 

rest against pipe

 

Pipe

 

 

 

Attic Insulation Shield

 

 

17 in. (432 mm)

 

 

diameter

 

6 Tabs bent

 

 

in 90°

 

Insulation

 

Insulation

13 in.

Pipe

Ceiling Firestop

(330 mm)

 

 

Figure 8.8 Install Attic Insulation Shield Below the Ceiling

Heatilator • Birmingham BIR42-B4059-681• 11/11

29

Page 29
Image 29
Hearth and Home Technologies BIR42-B owner manual Install Attic Insulation Shield, Prepare Attic Insulation Shield

BIR42-B specifications

Hearth and Home Technologies has consistently set the standard for modern heating solutions, and the BIR42-B gas fireplace is no exception. This model stands out for its blend of elegance, efficiency, and technology, making it a highly sought-after choice for homeowners looking to elevate their living spaces.

The BIR42-B features a sleek, contemporary design that seamlessly fits into various decor styles. Measuring 42 inches in width, it provides a generous viewing area to enjoy the mesmerizing flames while adding a focal point to the room. The fireplace comes with a choice of high-quality finishes, allowing homeowners to customize it to their aesthetic preferences.

One of the main features of the BIR42-B is its advanced heating capabilities. With an impressive BTU output, it efficiently warms spaces, making it perfect for both small and large rooms. This model is equipped with a design that maximizes heat circulation, ensuring that warmth is evenly distributed throughout the space.

The BIR42-B also incorporates innovative technologies that enhance user experience. The fireplace comes with a user-friendly remote control, allowing homeowners to adjust flame height and heat settings from the comfort of their seat. This is particularly useful for those chilly evenings when a quick adjustment can make all the difference.

Safety is a primary concern when it comes to heating appliances, and Hearth and Home Technologies has gone the extra mile with the BIR42-B. The unit includes safety features such as an automatic shut-off system and thermal sensors, ensuring peace of mind for users and their families.

Another impressive characteristic is the fireplace's clean-burning technology, which not only adheres to environmental standards but also promotes better air quality inside the home. The BIR42-B is designed to minimize emissions, making it an eco-conscious choice for homeowners.

In summary, the BIR42-B by Hearth and Home Technologies is a top-tier gas fireplace that expertly combines style, functionality, and safety. With its modern design, advanced heating capabilities, user-friendly features, and commitment to environmental responsibility, it stands as an excellent investment for those looking to enhance their home’s ambiance and comfort. This model not only promises warmth but also becomes a central element of design and leisure in any living space.