Installation

Place the stove in the intended position and lift out the hotplate, checking that the joint between the underside of the hob and the top of the stove is intact. Any joints which have opened should be made good with the fire cement provided.

Replace the hotplate making sure that it is seated evenly on the soft rope and that it is approximately 0.1” (1.5mm) higher than the enamelled top plate, with an equal space all round. Fit the flue chamber which should have a rope seal already installed. The flue chamber is screwed to the stove making a good seal as any air leak at this point will impede the working of the stove.

P/N - RS4M301136 A

Flue Chamber Box is located in Main Oven compartment during shipment.

Remove all bubble wrap and protective film from inside of oven doors prior to stove ignition.

Refer to Fig. 7 for definition of terms and installation orientation of Flue Chamber.

a.Remove two screws (1/4” x 20) and fiber washers from oven top cutout.

b.Prior to positioning Flue Chamber, ensure that chamber damper is in its full open position to allow for access to screw hole locations.

c.Position Flue Chamber on stove top ensuring that it is nested as close as possible to the stove top, to allow for a minimal gap - front and side.

d.Install fiber washers and 1/4” x 20 screws - ensuring fasteners are tightly securing Flue Chamber.

e.Close Flue Chamber door.

Open the firebox and ashpit doors and check that the reciprocating bottom grate bars are in position. Make sure the three restriction plates are in place on the bottom grate

-one at the front and two at the rear. The riddling lever will not operate with restriction plates in place - it is intended for cleaning purposes only.

Be sure to read the sections on clearances, floor protection and chimneys before actively starting the installation.

A woodburning stove radiates heat in all directions. Heat directed toward living areas in front of the stove is usually very welcome. However, heat radiating in other directions will not be as welcome if it results in overheating nearby walls, ceilings and floors.

An important part of planning a safe installation is to be sure that the combustible material located near your stove does not overheat.

Clearance is the distance between your stove and stovepipe and nearby walls, ceilings and floors.

If there is adequate clearance, then the nearby surfaces will not overheat.

It is very important that you match the stove pipe you are

using to the clearances specified. Failure to do so will result in an unsafe condition.

Unit must be placed on a continuous non-combustible pad (floor tile with grouting or sheet metal pad) extending 21” (540mm) in front and 8” (203mm) to the side and back.

Air flowing between the stove pipe and nearby surfaces carries away heat. Do not fill the empty space with any insulating material.

A chimney approved to CSA B.365-01 in Canada or NFPA 211 in the USA must be used to connect to the stove pipe.

Fig. 1

DESN 515137

 

 

Handrail:

The handrail brackets are held on the front ends of the stove top-plate casting. Remove the travel nuts and replace with the handrail brackets ensuring the fibre protecting washers are in position. Insert the handrail with fitted endcaps into the brackets, positioning them correctly, and tighten the locating bolts (See Fig. 1). Do not use handrail to move stove.

Endcaps, brackets and hardware, referenced in Fig. 1 are located in the lower warming drawer during shipment. Handrail is located on Stovetop in a round tube during shipment.

Do not hang combustible material on handrail during stove operation.

Warning

The ashpit and firebox door must be closed during normal use, except when lighting or refuelling

Clearances must be maintained at all combustible material. These include doors, trim, furniture, drapes, newspapers and clothes. See local codes for a description of combustible material.

Make sure that no floor or chimney supports will be cut due to chimney installation.

Contact local building officials about restrictions and installation inspection in your area.

6

Page 5 Page 7
Page 6
Image 6
Heartland Wood Stove warranty Installation, RS4M301136 a, Handrail
Page 5 Page 7

Wood Stove specifications

Heartland Wood Stove is a premier choice for homeowners seeking a reliable and efficient heating solution. This wood-burning stove combines traditional aesthetics with modern technology, making it a perfect addition to any home that values both comfort and style.

One of the standout features of the Heartland Wood Stove is its exceptional heating capacity. The stove is designed to effectively heat large spaces, providing warmth and a cozy atmosphere during the coldest months. With a robust firebox and an expansive fuel capacity, it can burn for hours on a single load of wood, minimizing the need for frequent refueling.

In terms of design, the Heartland Wood Stove showcases a classic look that complements a variety of decor styles. Its sleek lines and elegant finish make it a focal point in any room. The stove is available in various colors and finishes, allowing homeowners to choose a model that suits their taste and home environment.

One of the most innovative technologies integrated into the Heartland Wood Stove is the secondary combustion system. This system optimizes fuel efficiency by burning off gases and particulates that would otherwise escape through the chimney. As a result, the stove not only provides more heat from less wood but also reduces emissions, making it an environmentally friendly option.

Additionally, the Heartland Wood Stove features an air-wash system that keeps the glass door clean and free from soot buildup. This ensures that the beautiful flames are always visible, enhancing the ambiance of any space. The air-wash system operates by directing air over the glass, preventing the accumulation of creosote and other debris.

Furthermore, the stove is equipped with adjustable dampers, allowing users to easily control the burn rate and heat output. This flexibility ensures that homeowners can tailor the heating to their specific needs, whether they are looking for a gentle warmth or intense heat during frigid nights.

Safety is also a priority with the Heartland Wood Stove. It comes with a built-in heat shield and strong construction, minimizing the risk of overheating or accidental fires. The clearances required for installation are reasonable, making it easier for homeowners to fit the stove into their existing spaces.

In summary, the Heartland Wood Stove combines beauty, efficiency, and innovative technology, making it an outstanding choice for those who appreciate the warmth and charm of wood heating. Its combination of classic design and modern features ensures that it not only heats homes effectively but does so with style and efficiency.
Top Page Image Contents