SETUP Example – Set Up Receivers
Following is one example of how the Lighting Control Panel can be programmed to operate multiple light sources within a home.
The Control Panel has two “Groups” (A and B) with up to eight lighting controls in each group. In this example, the eight controls within Group A will operate the following light sources: Family Room (3), Kitchen, Front Porch, Rear Porch, Garage, and Foyer.
Light: Family Room Lamp #1 and #2 |
| Light: Family Room Ceiling Light | ||||||
| Receiver: Wall Switch |
| ||||||
Receiver: |
|
|
| |||||
|
| Wall Switch Code Setting: |
| |||||
|
|
| 1 2 3 4 | |||||
A | B |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
1 2 3 4 |
|
|
|
|
|
|
| |
| ALL ON | ALL OFF | Light: Foyer |
| ||||
|
|
| Receiver: Wall Switch |
| ||||
| ON DIM | OFF | Wall Switch Code Setting: | 1 2 3 4 | ||||
|
|
|
|
|
| |||
Light: Family Room Lamp #3 |
|
|
|
|
|
|
|
|
Receiver: Wall Receptacle |
|
| Light: Garage |
| ||||
Receptacle Code Setting: |
|
|
| |||||
1 2 3 4 |
| Receiver: Lamp Socket |
| |||||
|
|
| ||||||
|
|
| Lamp Socket Code Setting: | 1 2 3 4 | ||||
Light: Kitchen |
|
|
| Light: Rear Porch |
| |||
|
|
| Receiver: Floodlight |
| ||||
Receiver: Wall Switch |
|
|
| Floodlight Code Setting: | 1 2 3 4 | |||
Wall Switch Code Setting: | 1 2 3 4 |
|
|
|
|
|
|
|
| PANIC |
| Code Selection |
| ||||
|
|
| Switches |
|
| |||
Light: Front Porch |
|
| ON |
|
| Group Selection Switch | ||
|
|
|
| (Group A Shown) |
| |||
|
|
|
|
|
|
| ||
Receiver: Wall Switch | 1 2 3 4 |
|
| 2 |
|
|
|
|
Wall Switch Code Setting: |
| 1 | 3 |
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
| 4 |
|
| |
|
|
|
|
|
|
|
| |
Note:The“X”has been placed on the switches to
Note: Label containing code information is located underhelp clarify the code settings on this page. control identification card for user convenience.
Set code switch 4 on receivers to Group A setting (down) for all | To set receivers to work with Group B controls, slide code switch | |
receivers to operate in Group A. | 4 to Group B (up) on receivers and set code switches 1 through | |
Set code switches 1 through 3 on receivers to match the cor- | 3 as shown above. | |
responding control setting in above example. | Possible Light Sources for Group B: | |
To Operate: | • | Bedroom #1 (Wall Switch) |
1. Press Group A button (Note: Group A LED will be ON). | • Bedroom #2 (Wall Switch) | |
2. Press corresponding control button for desired action of selected | • | Master Bedroom (Wall Switch) |
light source. | • | Master Bedroom Lamp #1 |
| • Master Bedroom Lamp #2 | |
| • | Master Bath (Wall Switch) |
| • | Closet (Lamp Socket Converter) |
| • | Hall Ceiling Light (Wall Switch) |
