Model SL-5412
Features
•Turns on lighting when motion is detected.
•Automatically turns lighting off.
•Photocell keeps the lighting off during daylight hours.
•LED indicates motion was sensed (day or night).
This package includes:
Plastic Hanger
OPERATION
Mode: | Works: Day | Night | |
|
|
|
|
Test | 5 Sec | x | x |
Auto | 1, 5, 10 min. |
| x |
Manual | Until Dawn* |
| x |
|
|
|
|
* resets to Auto Mode at dawn.
Note: When first turned on wait about 1 1/2 minutes for the circuitry to calibrate.
TEST
Put the |
| |||||||||
of the sensor in the TEST position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 10 5 1 TEST | |||||||||
|
|
|
|
|
|
|
|
|
|
|
AUTO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Put the | ||||||||||
or 10 minute position. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| 10 5 1 TEST | |||||||||
|
|
|
|
|
|
|
|
|
|
|
MANUAL MODE |
|
|
|
|
|
|
|
|
|
|
Lamp Holders
2 Shells
Cover | Gasket | |
Plate | ||
Sensor | ||
| ||
Light Control | 6 Screws | |
| (3 sizes included) |
Manual mode only works at night be- cause daylight returns the sensor to AUTO.
Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE.
Manual mode works only with the ON- TIME switch in the 1, 5, or 10 position.
1 Second OFF
then...
Mounting Strap
Mounting Bolt
Rubber Plug | 2 Wire | |
Connectors | ||
|
Requirements
•The Light Control requires
•If you want to use Manual Mode, the control must be wired through a switch.
•Some codes require installation by a qualified electrician.
•This product is intended for use with the enclosed gasket and with a junction box marked for use in wet locations.
|
|
|
|
|
|
|
| ... back on. |
|
|
|
|
|
|
|
|
|
| Mode Switching Summary | |||||||
|
|
|
|
|
| |||
| TEST |
|
|
|
|
| Move | |
|
|
| ||||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 1, 5 or 10 minutes |
|
|
|
|
|
|
| ||
| AUTO |
|
|
|
|
| Flip light switch off | |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| for one second then |
|
|
|
|
|
|
|
| back on* |
MANUAL MODE |
|
|
| |||||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
*If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control will be in the AUTO mode.
© 2003 DESA Specialty Products™ |