Hitachi 42HDM12 important safety instructions Viewing, Important Notes

HOW TO SETUP YOUR NEW HITACHI PLASMA MONITOR

VIEWING

The major benefit of the HITACHI Plasma Monitor is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing. The best picture is seen by sitting directly in front of the monitor and about 8 to 18 feet from the screen.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the monitor can be located in a different section of the room.

If the monitor’s audio output will be connected to a Hi-Fi system’s external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the monitor, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

IMPORTANT NOTES

No. Items

1Arching sound from plasma monitor panel.

2Interference for infrared equipment.

3Bright and dark spots

4Picture Image (Spectrum)

5Plasma display panel surface temperature is too high

6Plasma Surface

7Transportation

8Image retention

9Luminosity and contrast

10Granular spots

11Disturbance to video apparatus

12Lip Sync

13About the use environment of plasma monitor (temperature)

14Caution on prolonged storage

15Operating

16Storage

17Power ON or OFF

Notes

A buzzing sound might be heard when the plasma monitor is turned on in a very quiet room. This is due to the plasma display panel drive circuit when it is functioning. This arching sound is normal and it is not a malfunction. Some infrared rays are emitted from the plasma monitor’s panel that might affect other infrared controlling equipment.

High-precision technology is used to manufacture the plasma display panel; But in some cases, there are minor defects in some parts of the screen. Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc. Some pixels will always be on or always off. Please note that this is not a malfunction.

When receiving still picture signals, (e.g. channel number indication or clock indication) for a while, you can see image-like when the picture varied. This is not a defect.

The plasma display panel is lighting the phosphors by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction. The Plasma monitor surface temperature is higher than a Cathode-ray-tube.

The plasma display panel is made from glass. Heavy shock on the front panel might damage it.

When the plasma monitor is transported horizontally, the glass panel has the possibility of being broken or increasing the picture defects. At the time of transportation, horizontal style is prohibited. More-over, please treat the plasma panel with great care because of a precision apparatus. Please instruct transporters so that it should be put into the packing box at the time of shipment. (There is a possibility that breakage of the panel or defects will increase.) Rough transportation might cause damage to the panel and pixel failure.

The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images.

Tips to prevent such image retention are:

-Do not display images having sharp brightness differences or hi-contrast images, such as monochrome characters and graphic patterns, for long.

-Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen saver function.

-Turn down the contrast and brightness controls.

Plasma monitor has luminosity and low contrast compared with CRT monitor.

When a screen is seen at point-blank range, a random fine grain may be visible to a dark part.

If an apparatus (VCR, etc.) antenna line is arranged near the monitor, the image may shake, or disturbance may be received.

There is some time lag between the picture and the sound. You can see lip motion that is delayed compared to the sound.

Electric discharge/luminescence characteristic of the plasma display panel also changes with peripheral temperature. Moreover, since there is also high power consumption value, a specified temperature environment is required.

Storing the plasma monitor for a period of more than 2 to 3 months without use might cause an unstable picture when the set is turned on.

Operating altitude: 800 to 1,114hPa (6,194ft to -2,484ft). Operating temperature: 41°F to 95°F.

Storage Altitude: 300 to 1,114hPa (31,912ft to -2,484ft). Storage temperature: 5°F to 140°F.

Frequent use of the Power ON or OFF might trigger the power protection circuit. If the monitor does not turn ON, please wait a little before turning ON again.

10