HITACHI SuperDrive
WARRANTY
HITACHI SuperDrive tools and system components are warranted to the original purchaser at retail to be free from defects in material and workmanship one year from the date of purchase.
The warranty shall only cover defects and not normal wear and tear, which occurs with use.
HITACHI SuperDrive assumes no responsibility whatsoever for malfunctions, failures or defects resulting from misuse, abuse, neglect, alteration or modification. SuperDrive makes no warranty and shall not be liable as to the fitness of its tools or fasteners for any particular uses or applications. No other warranties, representations or promises as to the quality or performance of the SuperDrive fastening tool other than those contained herein are made.
ANY IMPLIED WARRANTY GRANTED UNDER STATE LAW, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO DURATION TO THE EXPRESS WARRANTY GRANTED HEREUNDER. SUPER- DRIVE IN NO EVENT SHALL BE LIABLE FOR DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.
Operating Instructions
For SuperDrive 75 Series
OPERATION
1. Check Driver Bit to make sure it is in good con- |
dition. |
• If it is broken or worn out, install a new one. |
2. IMPORTANT! Make sure the |
switch is in the forward position. |
3. Insert a strip of screws into the feed track. Pull |
it through and insert the front into the index mod- |
725413
725470 | 725471 |
|
PARTS LIST - 75 SERIES TOOL | QTY | |
725414 | MODULE (GREEN DOT) | 1 |
725415 | SPRING (GREEN) 1.7mm | 1 |
725413 | NOSEPIECE FLAT HEAD SCREW |
|
| M4x10mm | 1 |
725470 | NOSEPIECE SUBFLOOR AND |
|
| 1 | |
ule until the first screw is in driving position in the |
center of the nose piece. See Figure 1. |
725414 (GREEN DOT)
725475
725472 725473
725416 | 725474 | 725424 |
725416725422
725425
725432
725415 (GREEN)
725471 | NOSEPIECE DECK/DRYWALL | 1 |
725425 | END PLATE FOR 75 | 1 |
725424 | WING SCREW FOR END PLATE | 1 |
725423 | BODY HEX SOCKET CAP SCREW |
|
| M4x8 | 1 |
725422 | BODY HEX SOCKET CAP SCREW |
|
| M4x10 | 2 |
725416 | RETAINER SCREW - M3x6 | 2 |
725416 | RETAINER FOR MODULE 3mm | 2 |
725427 | BRACKET FOR FEEDTRACK | 2 |
725428 | FEED TRACK HEX SOCKET SCREW |
|
| 5 | |
725426 | FEED TRACK | 1 |
725432 | TUBE FOR END PLATE | 1 |
DEPTH ADJUSTMENT PARTS | QTY | |
725472 | DEPTH CONTROL RETAINER | 1 |
725474 | DEPTH CONTROL SPRING | 1 |
725473 | DEPTH CONTROL ADJUSTMENT |
|
FIGURE 2.
725428
725427
| WHEEL | 1 |
725475 | SNAP E RING E2 | 1 |
725423 | 725426 | EXTENSION PARTS | QTY | ||
725476 | EXTENSION 19” | 1 | |||
|
| ||||
|
| 729430 | BIT EXTENSION | 1 | |
|
| 729431 | HANDLE ASSEMBLY | 1 | |
725430
725431
725476
Call
Appx. 1/4”
FIGURE 1.
4.Adjust the nosepiece so there is a 1/8” to 1/4” gap between nose piece and tip of screw.
•Tighten the nosepiece screw securely. See Figure 2.
5.Follow instructions on the sticker. Push slider in to adjust. Then turn knob until it locks.
FIGURE 3.
6.Turn on the motor before starting to drive screws.
•The motor can be locked to the ON position.
