OPERATION CONT.
7.Press the nosepiece with constant force against the work surface. Do not remove the tool from work surface until the clutch disengages and the bit stops rotating, signaling a fully driven screw.
8.Lift the tool enough to relieve all down pres- sure, allowing the feed mechanism to complete a full stoke before starting to drive another screw. The tool must complete a full stoke to advance screws properly.
9.Fine tune screw depth by first unplugging screwgun from electrical supply, then adjusting depth control as shown in Figure 3.
TROUBLESHOOTING
Screws are turning but not driving at all.
1.IMPORTANT! Be sure the screwgun is set to for- ward and not reverse.
2.Broken or worn out driver bit.
•Call
Screws are miss-driving.
What causes mis-drives?
1.Broken or worn out driver bit.
2.Operating the SuperDrive too fast.
3.Not lifting the SuperDrive off the work surface before driving the next screw.
4.Roller bearing is slipping during the indexing cycle.
• Pull the strip in reverse, if it slips or comes out, the index module is worn and must be replaced.
5.Strip is binding in the index module.
•Check for debris that may be built up in the in- dex module.
6. Burrs on the front face of the tool body prevent- ing complete cycling of the index module.
•Remove the burrs with a file.
7.Nose piece screw is loose and rubs on the tool body preventing full cycling of the index module.
• Tighten the nose piece screw securely.
8.Nose piece is bent and rubs on the tool body preventing full cycling of the index module.
• Straighten it with pliers or replace.
9. Strip is binding in the feed track.
Screws are not seating uniformly.
1.Not enough follow through in driving the screws.
2.Incorrect setting of the depth control bar. • Re- adjust.
3.Driver bit is worn and comes out of the recess before the screw is seated.fully.
• Call
4.If 3” screws stick up 3/8” you must call
Screws in the strip are being skipped.
If a screw is skipped and not driven, a tooth may be broken on the indexing gear.
• The index module must be replaced.
Screw strip slips or comes out effortlessly from in- dex module.
• Index module is worn and must be replaced.
Bit seems to wear rapidly.
If the depth control bar is set to drive screws too deeply, excessive torque is required and can cause excessive wear of the bit. Adjust the screw depth accordingly.
OTHER POINTS OF ATTENTION
1.If you lose the screw for securing the nose piece.
• Order item part # CWFB13.
2.If the end plate has been damaged from over tightening the wing screw, or the wing screw is broken and the end plate cannot be securely clamped to the coupler.
• Call
MAINTENANCE
1.Read section titled Safety Warnings before maintaining tool.
2.With tool unplugged from power supply, make daily inspection checking free movement of nose and trigger.
• Do not use if parts stick.
3.Occasionally lubricate the index module roller (as shown in photo as white dots).
• Lubricate with
4.Wipe tool with clean cloth daily and check for wear.
CHANGING THE INDEX MODULE OR SPRING
1.Remove retainers by loosening the screws and pushing in the index module about 1/4” so the retainers can be pushed back and taken out.
2.When replacing the index module make sure the indexing pin lines up with the entrance groove on the body.
CHANGING BIT
1.Due to wear or damage, the bit will need to be changed periodically or when changing from LOX, Phillips or Square Drive fasteners.
2.Loosen wing screw.
3.Remove bit.
4.Insert new bit.
SAFETY WARNINGS
READ AND FOLLOW ALL INSTRUCTIONS
1.Keep work area clean and well lit. Cluttered benches and dark areas invite injury.
2.Avoid dangerous environment. Do not expose power tool to rain. Do not use power tools in damp or wet locations. Do not use tool in pres- ence of flammable liquids, dust or gases. Power tools can create sparks which might ignite the dust or fumes.
3.Keep bystanders, children and visitors away while operating a power tool. Distractions can cause you to lose control.
4.Guard against electrical shock. Prevent body contact with grounded surfaces.
5.Double insulated tools are equipped with a po- larized plug (one blade is wider than the other). This plug will fit in the outlet only way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.
6.Do not abuse cord. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cord immediately. Dam- aged cords increase the risk of electrical shock.
7.When operating tool outside, use an outdoor extension cord marked with
8.Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
9.Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, cloth- ing, and gloves away from moving parts. Loose clothes, long hair, or jewelry can be caught in moving parts.
10.Avoid accidental starting. Be sure switch is off before plugging in the tool. Carrying tools with your finger on the switch or plugging in the tool with the switch on invites accidents.
11.Remove adjusting keys and wrenches before turning the tool on. A wrench or key that is left at- tached to a rotating part of the tool may result in personal injury.
12.Do not overreach. Keep proper footing and balance at all times.
13.Use safety equipment. Always wear protective glasses. Dust mask,
14.Secure work. Use clamps or other practical way to secure and support the work piece to a stable platform. This leaves both hands free to operate the tool.
15.Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which it is de- signed.
16.Store idle tools. When not in use, tools should be stored in dry and high or locked
17.Disconnect the plug from power source be- fore making adjustments, changing accessories, or storing tool.
18.Maintain tools with care. Keep tool clean. Fol- low instructions for lubricating and changing ac- cessories.
19.Check for misalignment or binding of moving parts, and other conditions that may affect op- eration. If damaged have the tool serviced by a Grabber authorized service center before using.
20.Use only accessories recommended by manu- facturer of tool. Accessories that are suitable for one tool may become hazardous when used on another tool.
21.Repairing tool. Any repairs to electric tools should be performed only by qualified personnel. Use only authorized parts.
